Configuring Timer Settings; Setting The Alarm; Configuring World Time Settings; Adjusting Hand Alignment - Casio 5638 Operation Manual

Configuring Timer Settings

Make sure that the symbol is shown on the
e
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to configure the timer time
setting.

Setting the Alarm

Make sure that the symbol is shown on the
e
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to configure alarm time
settings.
Configuring World Time
Settings
Specifying a World Time City with EDIFICE
Connected causes the watch's World Time
City to change accordingly. Watch settings
can be configured to perform auto summer
time switching for the World Time City.
Make sure that the symbol is shown on the
e
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
Operation Guide 5638
Note
EDIFICE Connected World Time lets
●
you select from among approximately
300 cities as the World Time City.
Selecting a World Time City
●
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen. The World Time setting will
be reflected on the watch.
Note
You can use EDIFICE Connected to
●
select from among World Time cities in
addition to those built into the watch.
The additional cities can be selected
only by using EDIFICE Connected.
Configuring the Summer Time Setting
●
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to select a summer time
setting.
"Auto"
●
The watch switches between standard
time and summer time automatically.
"OFF"
●
The watch always indicates standard
time.
"ON"
●
The watch always indicates summer
time.
Note
While the summer time setting is
●
"Auto", the watch will switch between
standard time and summer time
automatically. You do not need to
switch between standard time and
summer time manually. Even if you are
in an area that does not observe
summer time, you can leave the
watch's summer time setting as "Auto".
For information about summer time
●
periods, refer the "Summer Time
Table" or EDIFICE Connected.
Swapping Your World Time and Home
●
Time
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to swap your Home Time
with your World Time.
Note
Auto time adjustment does not work for
●
24 hours after swapping of the Home
Time and World Time.

Adjusting Hand Alignment

If the hands are out of alignment even though
the watch is connected with your phone, use
EDIFICE Connected to adjust them.
Make sure that the symbol is shown on the
e
●
watch display when you perform the
procedure below.
If is not displayed, refer to the information
e
●
at the link below.
Connecting with a Phone
l
1. Y
Tap the "EDIFICE Connected" icon.
2. Y
Perform the operation shown on the
phone screen to correct hand alignment.

Phone Finder

You can use phone finder to trigger a tone on
the paired phone to help you find it. The tone
is forced to sound even if your phone is in
vibrate mode.
Important!
Phone finder will not sound the tone
●
unless EDIFICE Connected is running
on the phone.
Do not use this function in areas where
●
phone call tones are restricted.
The tone sounds at a high volume. Do
●
not use this function when listening to
phone output over earphones.
1. X
If the watch is in any mode besides the
Timekeeping Mode, hold down (C) for at
least two seconds to enter the
Timekeeping Mode.
8