Related Manuals for Toro TimeCutter 79335
Summary of Contents for Toro TimeCutter 79335
- Page 1 Form No. 3375-960 Rev B 50in Bagger TimeCutter ® Riding Mower Model No. 79335—Serial No. 313000001 and Up *3375-960* B Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Setup ................5 1 Installing the Weight..........6 You may contact Toro directly at www.Toro.com for product 2 Installing the Engine Guard........8 and accessory information, help finding a dealer, or to register 3 Installing the Bagger Frame ........8 your product. -
Page 3: Safety
Follow the attachment manufacturer's recommendation for weight limits for towed equipment and towing on slopes. The following list contains safety information specific to Toro products and other safety information you must know. • Never allow children or others in or on towed equipment. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Bolt (3/8 x 1-1/4 inches) Lock nut (3/8 inch) Weight mounting bracket, left Weight mounting bracket, right Washers Install the weight. Weight holding bracket Bolt (3/8 x 1 inch) Flat weight Suitcase weight... -
Page 6: Installing The Weight
Installing the Weight Parts needed for this procedure: Bolt (3/8 x 1-1/4 inches) Lock nut (3/8 inch) Weight mounting bracket, left G014875 Weight mounting bracket, right Figure 3 Washers Weight holding bracket 1. Front right caster (castor 3. Bolt (3/8 x 1 inch) fork and wheel not shown Bolt (3/8 x 1 inch) for clarity) - Page 7 the forward fasteners in the foot assist lift pedal bracket. Secure the bracket using two bolts and two lock nuts (Figure 7). One locknut is from loose parts and the other is reused from earlier removal. G014878 Figure 5 1. Locknut (3/8 inch), existing 5. Hole, existing in frame G014883 2.
-
Page 8: Installing The Engine Guard
6. Install a flat weight to the holding bracket and move it rearward, flush with the bracket (Figure 9). Installing the Engine Guard Parts needed for this procedure: Engine guard Self tapping screw (5/16 x 3/4 inch) Procedure Note: Certain models will have an engine guard already installed. - Page 9 G010578 Installing the Bagger Frame Parts needed for this procedure: Bagger frame support bracket Support spacer plate Self tapping screw (5/16 x 3/4 inch) Figure 12 Bolt (5/16 x 1 inch) 1. Support bracket 2. Self tapping screws (5/16 x 3/4 inch) Lock nut (5/16 inch) Angled bracket 3.
-
Page 10: Assembling The Bagger Top
Assembling the Bagger Top Parts needed for this procedure: Bagger top G014884 Bagger screen Procedure Turn the bagger top over. Install the screen as shown in Figure 16 so it slopes down toward the collection bags. Make Figure 14 sure the screens snap into place and the tabs engage the 1. - Page 11 2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 18). Installing the Bagger Top Parts needed for this procedure: Grass Bag Upper bagger tube Procedure 1. Install the bagger top to the bagger frame. Rotate the bagger top to align the key holes in the bagger top brackets with the keys in the posts on the bagger frame (Figure 17).
-
Page 12: Installing The Cutoff Baffle
Installing the Cutoff Baffle No Parts Required Procedure Note: Certain models will have the cutoff baffle installed (Figure 20). Proceed to the next procedure if a cutoff baffle is installed. Important: The cutoff baffle was shipped with the machine as a loose part. 1. -
Page 13: Connecting With The Discharge Tube
3. On the top of the chute, engage the hook shaped latch around pivot rod of the deflector assembly as shown in (Figure 23). Connecting with the Discharge Tube Parts needed for this procedure: Discharge tube Procedure 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 25). -
Page 14: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. •... -
Page 15: Removing The Bagger
Removing the Bagger Operating Tips CAUTION Tips for Bagging Failing to remove the front bagger weights and operating the machine without the bagger Size attachment may cause an unstable condition which Remember that the mower is longer and wider with this could result in a loss of control. - Page 16 CAUTION As the bagger fills, extra weight is added to the back of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. • Do not start or stop suddenly when going uphill or downhill.
-
Page 17: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the bagger After the first 10 hours • Clean the bagger Before each use or daily •... -
Page 18: Caring For The Grass Bags
Caring for the Grass Bags Storage Washing the grass bags is not recommended. Storing the Bagger Attachment To prevent rapid deterioration of the bag material, store the bags where they will dry completely after each use. 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment. - Page 19 Notes:...
- Page 20 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.