SystemAir Fantech 2VLD12 Series Operational Manual

SystemAir Fantech 2VLD12 Series Operational Manual

Standard-duty venturi-mounted direct-drive exhaust fans

Advertisement

Quick Links

2VLD12 - 2VLD24 Series
Standard-Duty Venturi-Mounted
Direct-Drive Exhaust Fans
United States
10048 Industrial Blvd., Lenexa, KS, 66215
Tel.: 800.747.1762 • Fax: 800.487.9915
Canada
50 Kanalflakt Way, Bouctouche, NB, E4S 3M5
Tel.: 800.565.3548 • Fax: 877.747.8116
Operational and Parts Manual
Item #: 481803
Rev Date: 2016-07-21
Fantech, Inc. and Systemair Mfg.
certify that the ventilators shown
herein are licensed to bear the
AMCA Seal. The ratings shown are
based on tests and procedures
performed in accordance with
AMCA Publication 211 and AMCA
Publication 311 and comply with
the requirements of the AMCA
Certified Ratings Program.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fantech 2VLD12 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SystemAir Fantech 2VLD12 Series

  • Page 1 Operational and Parts Manual 2VLD12 - 2VLD24 Series Standard-Duty Venturi-Mounted Direct-Drive Exhaust Fans Fantech, Inc. and Systemair Mfg. certify that the ventilators shown herein are licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures...
  • Page 2 Note Warning / Information Technical Practical tip Important information note Please read and save these instructions. Read carefully before Caution: In United States, to reduce the risk of injury to persons, OSHA attempting to assemble, install, operate or maintain the product complying guards are required when fan is installed within 8 feet of floor, described.
  • Page 3 Description Venturi-mounted exhaust fans are used for commercial, industrial, and farm building ventilation. Wire intake guard complies with United States OSHA Federal 1/2” max. opening requirement and has baked-on charcoal grey metallic polyester finish to resist corrosion. All units are supplied with aluminum propeller with a galvalume coated spider.
  • Page 4: Installation

    Installation 1. The unit should be securely mounted in a rigid framework. Single Speed Allowing the fan frame to flex or move will result in undue Common Line 1 vibrations and possible premature motor or propeller failure. Common Line 2 2.
  • Page 5 For repair parts, call 1.800.565.3548 Figure 4: Repair parts illustration Ref no. Description Propeller Venturi panel Guard Motor Yoke brace #10-32 Spinlock nut* 1/4”-20 x 1/2” HHC screw* 1/4”-20 Flange spinlock nut* 3/8”-24 Flange spinlock nut* #10 x 3/4” Flatwasher* 3/8”-24 x 1”...
  • Page 6: Troubleshooting

    Troubleshooting Symptom Possible causes Corrective Action Excessive noise 1. Dry motor bearings 1. Relubricate motor bearings 2. Loose propeller 2. Tighten setscrews in hub 3. Crooked or damaged propeller 3. Replace Fan inoperative 1. Blown fuse or open circuit breaker 1.
  • Page 7: Limitation Of Warranty And Liability

    Warranty Fantech, Inc. warrants to the original purchaser that our products will be found to be defective. Failure by purchaser to give such written notice free from defects in material and workmanship for a period of one (1) within the 30-day time period shall be deemed an absolute and uncondi- year from the date of shipment.
  • Page 8 Fantech reserves the right to make technical changes. For updated documentation please refer to www.fantech.net Fantech®...

This manual is also suitable for:

Fantech 2vld24 series

Table of Contents