CONTENTS EU Directives and UKCA Standards..............3 Important Information and Health & Safety............4 Components for Suites and Stoves............... 5 Installation......................6 Model Dimensions..................7 Installation (Wall Mounted Suites)............... 8 Installation (Suites with Risers and Stoves)..........11 Installation (Suites with Risers and Stoves)..........11 Installation (Floor-based)................13 Installation (Floor-based)................13 Installation (Cassette style).................15...
Page 3
Particular requirements for room heaters Particular requirements for room heaters UKCA STANDARDS All Evonic Fires products are in conformity with the relevant UK Statutory Instruments All Evonic Fires products are in conformity with the relevant UK Statutory Instruments (and their amendments).
IMPORTANT INFORMATION AND HEALTH & SAFETY When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: • Read all of the instructions carefully before using the appliance, only use this appliance as described in this manual.
Page 8
INSTALLATION INSTALLATION REQUIREMENTS Before installing the appliance please read and take into account the following important requirements; • The appliance must never be installed in front of an electrical socket. • The appliance must not be installed anywhere that it may come into contact with water, i.e.
Page 10
Determine the finished height and position that you want the appliance to be located. Then secure the wall bracket to the wall in the position you need using the wall plugs and screws provided. If you’re not securing the appliance to a masonry wall you will need to use the appropriate fixings.
Page 12
INSTALLATION INSTALLATION REQUIREMENTS Before positioning the appliance please read and take into account the following important requirements; • The appliance must not be located anywhere that it may come into contact with water, i.e. a bathroom. • This appliance is only suitable for indoor use, do not use outdoors. •...
Page 14
INSTALLATION REQUIREMENTS Before positioning the appliance please read and take into account the following important requirements; • The appliance must not be located anywhere that it may come into contact with water, i.e. a bathroom. • This appliance is only suitable for indoor use, do not use outdoors. •...
Page 16
INSTALLATION TOOLS REQUIRED • Tape Measure • Screwdriver • Pencil • PZ2 Screw Bit • Spirit Level • Screws (Supplied) INSTALLATION REQUIREMENTS Before installing the appliance please read and take into account the following important requirements; • Consult a qualified professional to check the structure of the installation site. •...
Page 17
INSTALLATION STEPS Once your studwork frame has been constructed, slide the appliance into the prepared void. Once you have slid the appliance into place, you can then go about securing it in position by screwing it into the studwork frame. There are 4 holes located in each corner .
Page 18
Once you have secured the fire into place, adding the outer frame is the final stage. The outer frame of the C600 comes with either a 3-sided or 4-sided frame, which are both attached using the same method. The frame uses a a combination of magnets and a push fit method.
FRONT AND SIDE GLASS INSTALLATION INSTALLATION Pivot Install Slotted Install Slide Install Bergen Bergen Banff Banff Halden Halden Midori Midori Banff R Banff R Canto 200 Canto 200 Halmstad Halmstad Locanda 175 Locanda 175 Tuva Tuva Espire 150 Espire 150 C600 C600...
Page 23
PIVOT INSTALL The pivot install of the front glass applies to the Bergen, Midori, Canto 200, Locanda 175, Espire 150, Murano, Mirada, Imperium, Crenshaw, Inglewood, Ellipse and all Rivera’s. The model shown in this example is an E1030, but the same process applies to all fifteen models. Unscrew and remove the top and bottom glass retainer panels.
Page 24
Apply the Suction Lifter to the glass and apply the glass to the bottom edge first, then pivot into the appliance. Warning The Suction Lifter is provided to assist in moving the glass NEVER as the sole support of the glass. Always support the glass throughout the entire process until the glass is fully fitted.
Page 25
SLOTTED INSTALL The slotted install of the front glass applies to the Banff, Banff R, Halmstad, and Tuva. The model shown in this example is the Halmstad, but the same process applies to all three models. To install the front glass first locate the four keyhole slots on the front of the appliance, and the four screws on the back of the front glass.
Page 26
SLIDE INSTALL The sliding install of the front glass applies only to the Halden model. To remove the glass from the Halden model, first slide the lid back slightly, then lift. Warning Always support the glass throughout the entire process until the glass is fully fitted.
Page 28
Evoflame Only - LED Strip Replacement Scan the QR code to be taken to a video in our maintenance series. Please note; this video shows an old method of removing the front glass panel. Refer to page 19 of this instruction manual for the new method.
Page 29
Failure to supply evidence to support your warranty claim may invalidate or delay the claim. Any visit by an Evonic Fires engineer will incur a service charge after the first year. We will not accept or reimburse the cost(s) of any third party who undertakes any work carried out on the product or fits parts, unless we have approved such work in advance of it being carried out.
Page 30
For product sold outside the UK and Ireland, UK law will prevail. The Evonic Fires Extended Warranty does not affect your statutory rights. CK Fires Ltd / Evonic Fires...
Need help?
Do you have a question about the Banff R and is the answer not in the manual?
Questions and answers