Table of Contents
Advertisement
Enabling one of the pre-set programmes
To activate one of the pre-set weekly programmes, proceed as
follows:
- press the M
/o
button, on the display flash
enu
k
- turn the CH knob
to select
- press the M
/o
button to access the parameters
enu
k
- turn the CH knob
in a clockwise direction until 105 appears
on the display
- press the M
/o
button to access heating zone selection
enu
k
- turn the CH knob
and select "Heating Zone 1"or "Heating Zone 2"
(if present)
- press the M
/o
button to confirm the selected zone
enu
k
- turn the CH knob
to select 106 "Pre-set Timers"
- press the M
/o
button to access the pre-set programme
enu
k
- turn the CH knob
to select one of the available programmes
(e.g. "Pre-set Timer 2") see page 8 for pre-set information
- press the M
/o
button to confirm the selection.
enu
k
- press the e
button to restore the normal display screen.
sc
The pre-set timer programme may be applied in heating zones 1
and . Proceed as above, select pre-set zone for setting 105 "select
programming zone"
Displaying the selected pre-set programme
To display the selected programme, access menu 1 again as
indicated above and turn the CH knob
Timer function" appears.
Press M
/
button to access the selection of timers to be
enu
ok
displayed. Turn the CH knob
(e.g. "Heating Zone 1").
Press the M
/
button again to confirm the selection; the
enu
ok
programme will be shown on the display (see note).
To activate the programmedschedule, after exiting the menu, press the
CLOCK button; the
symbol will appear on the display.
bar
Inverno
Winter
Note: the zone relating to the timer programme is displayed via
the symbols located above the timer
selection zone 1 displayed
selection zone displayed
selection hot water displayed
Changing the pre-set programme
In order to adapt the schedule programming to your own
requirements, the pre-set programme may be modified.
Access menu 1 as described on the previous page, then turn the
CH knob until the day(s) for which you wish to modify the pre-set
programme is (are) displayed.
E.g. 109 "Saturday -> Sunday" can be modified as shown below.
TIME BAND I
between 00.00 and 07.00
TIME BAND II
between 07.00 and .00
TIME BAND III
between .00 and .59
000
menu100
until 104 "Display Zone
to select the relevant heating zone
OFF Period
ON Period
OFF Period
Press Menu/ok to enter modification mode.
The text "Move Cursor" appears on the display; use the CH knob
the cursor over the period of time to be modified.
The cursor flashes and the selected time is indicated on the clock
(in steps of 15 minutes).
bar
Press the c
button
until the text "OFF
lock
Period" appears.
To programme a further inactive heating
period (e.g. "OFF Period" to remove an hour from
the ON period between 06.00 and 07.00).
Turn the CH knob
to move the cursor to
the relevant schedule.
bar
Periodo OFF
OFF period
Besides the modification of the time band shown on the display,
the clock indicates the selected time in steps of 15 minutes.
Once the modification of the pre-set period is complete, press
the c
button
and select "On period" to programme another
lock
operating stage, in our example this is a single period between
bar
Periodi ON
ON period
07.00 and .00.
Turn the CH knob
to move the cursor to the relevant time (.00
in our example). The cursor, when moved, will make the entire ON
bar
Periodi ON
period visible.
After performing all the modifications press the M
confirm the schedule programming modification.
Then press the e
button to restore the normal display screen.
sc
To activate the programmed schedule, after exiting the menu, press
the C
button ; the
symbol will appear on the display.
lock
If "OFF period" or "ON period" is selected, other periods may be entered
so that the programme is adapted to suit your own requirements,
even on a daily basis.
Daily programming may be modified by selecting the relevant day
(within menu 1) and entering new OFF periods and ON periods as
described above.
User's manual
to position
Muovi Cursore
Move Cursor
bar
Sanitario
ON period
/o
button to
enu
k
9
Advertisement
Table of Contents
