Advertisement
• To change the SET value, press the increase value button
"UP" :
or the decrease value button "DOWN":
• If no button is pressed for 60 seconds ("TIME OUT"), or by
pressing the "SET" button once, the digital thermostat
memorizes the last set value and the normal display is
restored.
The temperature range is set from a minimum to a maximum,
according to the following values:
Positive temperature models
• "MIN" setting = 0℃
• "MAX" setting = + 10℃
Negative temperature models
• "MIN" setting = – 2℃
• "MAX" setting = + 8℃
Low temperature - freezer models (fully insulated door)
• "MIN" setting = – 24℃
• "MAX" setting = – 15℃
Low temperature - freezer models (glass door)
• "MIN" setting = – 22℃
• "MAX" setting = – 15℃
Fish models
• "MIN" setting = – 7℃
• "MAX" setting = + 6℃
I I . . 2 2
D D i i g g i i t t a a l l t t h h e e r r m m o o s s t t a a t t s s i i g g n n a a l l l l i i n n g g i i c c o o n n s s
The digital thermostat has the following signalling icons:
lit up
This icon indicates compressor
activation.
lit up
This icon indicates the manual defrost
function in progress.
lit up
This icon indicates activation of com-
partment fans (if present) and/or
condenser.
lit up
This icon indicates that a temperature
alarm has occurred during appliance
operation.
lit up
This icon indicates that a service alarm
has occurred during appliance
operation.
I I . . 3 3
S S i i g g n n a a l l l l i i n n g g a a n n d d a a l l a a r r m m s s
I I . . 3 3 . . 1 1
S S e e r r v v i i c c e e a a l l a a r r m m s s a a n n d d s s i i g g n n a a l l l l i i n n g g f f o o r r m m o o d d e e l l s s 0 0
℃ ℃ / / + + 1 1 0 0 ℃ ℃ a a n n d d f f r r e e e e z z e e r r m m o o d d e e l l s s
The alarm is signalled by lighting up of the icon
signalling is also indicated by the alarm code appearing on the
display.
Example: Alarm signalling due to a faulty probe (compartment
probe) appears directly on the instrument display with the
message "E0" and "rE" flashing alternately (refer to position 1
of the alarms table).
26
When the alarm condition ceases, the alarm goes off.
Otherwise, contact the Customer Care Service.
I I . . 3 3 . . 2 2
S S e e r r v v i i c c e e a a l l a a r r m m s s a a n n d d s s i i g g n n a a l l l l i i n n g g f f o o r r m m o o d d e e l l s s - - 2 2 ℃ ℃ / /
+ + 8 8 ℃ ℃ a a n n d d f f i i s s h h m m o o d d e e l l s s
The alarm is signalled by lighting up of the Icon
Alarm signalling is also indicated by the alarm code appearing
on the display.
Example: Alarm signalling due to a faulty probe (compartment
probe) appears directly on the instrument display with the
message "E0" and "rE" flashing alternately (refer to position 1
of the alarms table).
Alarm signalling due to a faulty evaporator sensor (evaporator
sensor) appears directly on the instrument display with the
indication "E1" flashing (refer to position 2 of the alarms table).
I I . . 3 3 . . 3 3
T T e e m m p p e e r r a a t t u u r r e e a a l l a a r r m m s s a a n n d d s s i i g g n n a a l l l l i i n n g g ( ( c c o o m m m m o o n n t t o o
a a l l l l a a p p p p l l i i a a n n c c e e s s ) )
The alarm is signalled by lighting up of the icon
signalling is also indicated by the alarm code appearing on the
display.
Temperature alarm signalling, regarding the thermostatting
probe, appears directly on the instrument display with the
indication "HI" (max. temperature alarm) and "LO" (min.
temperature alarm).
I I . . 3 3 . . 4 4
D D o o o o r r o o p p e e n n a a l l a a r r m m s s a a n n d d s s i i g g n n a a l l l l i i n n g g f f o o r r h h i i g g h h
h h u u m m i i d d i i t t y y , , f f i i s s h h m m o o d d e e l l s s
When the door is opened the display starts flashing together
with the icon
minutes, the display shows the message dor (accompanied by
a beep), alternating with the temperature value. The alarm is
deactivated when the door is closed.
I I . . 4 4
D D e e f f r r o o s s t t
• A A u u t t o o m m a a t t i i c c d d e e f f r r o o s s t t ( ( e e x x c c l l u u d d i i n n g g f f r r e e e e z z e e r r m m o o d d e e l l s s ) )
The appliance has an automatic defrost function. This
function is signalled by lighting up of the "DEFROST" icon
.
The defrost water is run into a tray and automatically
evaporated.
• M M a a n n u u a a l l d d e e f f r r o o s s t t a a c c t t i i v v a a t t i i o o n n
Keep the "DOWN" button pressed for at least 5 seconds to
start a manual defrost cycle.
This function is signalled by lighting up of the "DEFROST"
icon
.
If defrost conditions do not exist, the display shows the
message "dFb", indicating that the operation will not be
carried out (o o n n l l y y f f o o r r - - 2 2 ℃ ℃ / / + + 8 8 ℃ ℃ a a n n d d f f i i s s h h m m o o d d e e l l s s ).
Defrost can be stopped manually by pressing the "DOWN"
button for a few seconds:
the display shows the message "dFb". Defrost cannot be
. Alarm
activated in the programming stage.
I I . . 5 5
S S w w i i t t c c h h i i n n g g o o n n a a n n d d t t e e m m p p e e r r a a t t u u r r e e a a d d j j u u s s t t m m e e n n t t
f f o o r r W W i i n n e e - - l l i i n n e e m m o o d d e e l l s s
This type of appliance provides for 5 temperature areas
designed for preserving various types of wine. This solution
allows the wine to be kept for a long time and served at an
. If the door remains open for more than a few
.
. Alarm
Advertisement
