Motorola 3260FAST User Manual page 140

Table A-1.
AT Commands, Cross-Referenced to Front Panel Options (Continued)
AT Parameter &
Command Option
*
AT DB3 =S38
DC
*
AT DC0 =Disable
*
AT DC1 =Enable
Dial Wait
*
AT DD0 =2 sec
*
AT DD1 =3 sec
*
AT DD2 =4 sec
*
AT DD3 =6 sec
*
AT DD4 =12 sec
*
AT DD5 =15 sec
*
AT DD6 =20 sec
*
AT DD7 =30 sec
*
AT DD8 =40 sec
*
AT DD9 =S7
DTE Rate
*
AT DE2 =300
*
AT DE4 =1200
*
AT DE5 =2400
*
AT DE6 =4800
*
AT DE7 =7200
*
AT DE8 =9600
*
AT DE9 =12.0
*
AT DE10 =14.4
*
AT DE11 =16.8
*
AT DE12 =19.2
*
AT DE13 =21.6
*
AT DE14 =24.0
*
AT DE25 =26.4
*
AT DE26 =28.8
*
AT DE15 =38.4
Gray shading indicates country-specific options. See Appendix C for your country's options.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Description
This setting allows the timer to start immediately upon detection of a disconnect request. The
request continues to process either its transmit or receive buffers. The modem disconnects
when the timer expires, regardless of the buffer states. NOTE: In Direct mode, no data
buffering occurs. However, the modem delays a disconnect until the timer expires.
Data Compression
Data compression is not attempted.
Data compression is attempted.
If the modem is using LAPM error correction, it uses V.42bis data compression when
DC=Enabled. NOTE: In an application with SDC enabled, LAPM error correction and
V.42bis data compression only are used.
If your modem is using MNP error correction, it attempts to negotiate V.42bis and MNP-5 data
compression with the remote modem.
Depending on which data compression type can be accommodated by the remote modem,
V.42bis or MNP-5 is used. Otherwise, no data compression is used.
Dial Wait
The modem waits 2 seconds for a dial tone.
The modem waits 3 seconds for a dial tone.
The modem waits 4 seconds for a dial tone.
The modem waits 6 seconds for a dial tone.
The modem waits 12 seconds for a dial tone.
The modem waits15 seconds for a dial tone.
The modem waits 20 seconds for a dial tone.
The modem waits 30 seconds for a dial tone.
The modem waits 40 seconds for a dial tone.
Dial wait is determined by setting S-Register 7. (See the "S-Registers" section in Chapter 5).
DTE Rate
The DTE port is configured for 300 bps.
The DTE port is configured for 1200 bps.
The DTE port is configured for 2400 bps (this is the lowest rate available in SDC mode).
The DTE port is configured for 4800 bps.
The DTE port is configured for 7200 bps.
The DTE port is configured for 9600 bps.
The DTE port is configured for 12,000 bps.
The DTE port is configured for 14,400 bps.
The DTE port is configured for 16,800 bps.
The DTE port is configured for 19,200 bps.
The DTE port is configured for 21,600 bps.
The DTE port is configured for 24,000 bps.
The DTE port is configured for 26,400 bps.
The DTE port is configured for 28,800 bps.
The DTE port is configured for 38,400 bps.
Configuration Quick Reference A-17