Bonsaii C144-D - 24-Sheet Cross Cut Shredder Manual

KNOW YOUR SHREDDER

1. Power switch ("-"=on,"0"= OFF)

2. Power button (green light under work status)

3. Bin full indicator light (green light under basket fulling status)

4. Overload &Overheat indicator light (Overload in red with flashing, Overheat in red)

5. FWD indicator light (FWD indicator light in green when Press FWD button)

6. REV indicator light (REV indicator light in green when Press REV button)

7. FWD button (green light under work status)

8. REV button (green light under work status)

9. Feed Opening

10. Transparent Window

11. Basket

12. Basket Handle

13. Shredder's Caster
14. Caster Brake

For safety reasons, shredder will operate only if the shredder head is in correct position and used with supplied basket.

TECHNICAL SPECIFICATIONS

Will not shred: large paper clips, Unopened junk mail, window or insulated envelopes, continuous forms, newsprint, bound pages (for example: notepads, checkbooks, magazines, etc...), transparencies, laminated documents, cardboard, any items with adhesives, hard materials or plastic (except plastic Credit Cards and CDs).

Maximum recommended daily usage rates: 130 sheets, 5 credit cards.

OPERATING INSTRUCTIONS

1. Plug in and press the power switch "-"
   
2. Power, FWD and REV buttons in green lights, it means under working status. (feed papers, credit card, clips, staple or CD to shred)
   
   Continuous operation around 60minutes.
   
   Beware of injury caused by CD splashing or incorrect CD shredding. Please wear safety goggles and shred the CD in a correct way.
   
3. When finished shredding, please press " power button" or "power switch" to "O"
   
   *Bin full: Bin full indicator light in green status, the shredder stops to work and need to clean the wastepaper.
   
   *Bin full indicator light will be OFF and Power& FWD&REV button will be in green with flashing when the basket is opened.
   
   After clean the basket and assemble the basket with shredder's body well, Bin full indicator light will be OFF, Power& FWD&REV button in green, Shredder is under staying working status.
   
   Jam: Press Rev button and take out of the jammed paper.
   
   Overloading: (Overload&Overheat indicator light in red with flashing status, the excess papers will be disgorged automatically and need to take out of excess papers by hand)
   
   Overheating: (Overload&Overheat indicator light in red status, need to await cooling down)
   
   Cool down around 40 minutes

PRODUCT MAINTENANCE

1. Plug in and press the power switch "-"
   
2. When power, FWD and REV button in green lights, feed one shredder lubricant pack to shred.
   
3. Press REV button for 2-3 seconds staying ( don't pull out the shredder lubricant pack)
   
4. Press FWD button 2-3 seconds staying
   
5. Repeat the operations from "REV" to "FWD" for 3-5times till the shredder lubricant pack is fully shredded.
   
6. When finished shredding, please press " power button" or "power switch" to "O".
   

* Only use the professional shredder lubricant pack to maintain the shredder such as Bonsaii shredder Lubricant 24-Pack(LS24)/12-Pack(LS12). (no cleaner, inflammable liquids, gages oil etc... )

TROUBLESHOOTING

Malfunction	Reason	Solution
Stop Working	The power plug doesn't connect to the power supply.	Please kindly check whether you use the machine with related supply voltage or Plug in again correctly.
	Power supply voltage is too low or no power supply.	Please kindly find a related supply voltage to use it.
	The machine is under overheating protection, because the machine is over the continues working capacity.	Wait for the machine to Cool down naturally.
	The thickness Of paper is too thin.	To make the paper thicker, You can add more papers or fold the paper.
	The machine is overloading, because the paper is over machine Ma.x sh redding quantities.	Reduce paper quantity with an acceptable amount and place the paper into the feeding opening of shredder again.
	Damage Of power cable.	Please replace the power cable with the same parameters by professional person or contact with our customer service.
	The basket is lull.	Empty the basket,
	Defective of machine.	Please kindly contact with our customer service.
Jam	Paper jam.	Please kindly use the function of "Reverse" to take out the excess paper.
Keep Running	Paper dust and other foreign objects cover the sensor, The location ot sensor is in the Shredder'S feeding opening 100k like glass beads or marbles.	Please unplug first and use soft cloth or cotton swab to clean the foreign objects without any cleaner or water If there are some paper scraps around the sensor area, please kindly use cotton swab or needle nosed pliers to take out the paper scraps. Please don't overexert and use Sharp tools to clean or poke the sensor to avoid damaging the sensor.
Loud Noise	The shredder is placed on an unsuitable place.	Change the location.

If the above answers can not solve your problems, please kindly contact with our customer service team via email customer-care@bonsaii.com

Please give us a chance to make it right and do better!
Contact Our friendly customer service department for help first. Replacements for missing or damaged parts Will be shipped.

Customer Service:

• customer-care@bonsaii.com
• 1-844-728-6917

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Bonsaii C144-D - 24-Sheet Cross Cut Shredder Manual