Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DLX2336T01
Summary of Contents for Makita DLX2336T01
- Page 1 INSTRUCTION MANUAL Cordless Hammer Driver Drill DHP343 DHP453 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DHP343 DHP453 Drilling capacities Masonry 10 mm 13 mm Steel 10 mm 13 mm Wood 25 mm 36 mm Fastening capacities Wood screw 5.1 mm x 63 mm 6 mm x 75 mm Machine screw No load speed High (2) 0 - 1,300 min Low (1) -
Page 3: Ec Declaration Of Conformity
SAFETY WARNINGS WARNING: Wear ear protection. WARNING: The noise emission during actual use of the power tool can differ from the declared General power tool safety warnings value(s) depending on the ways in which the tool is used especially what kind of workpiece is WARNING: Read all safety warnings, instruc- processed. - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct Do not use a power tool while you are tired or power tool will do the job better and safer at the under the influence of drugs, alcohol or med- rate for which it was designed.
- Page 5 Do not use a battery pack or tool that is dam- Always start drilling at low speed and with the aged or modified. Damaged or modified batteries bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
-
Page 6: Tips For Maintaining Maximum Battery Life
To install the battery cartridge, align the tongue on the also void the Makita warranty for the Makita tool and battery cartridge with the groove in the housing and slip charger. -
Page 7: Overload Protection
Indicating the remaining battery Tool / battery protection system capacity The tool is equipped with a tool/battery protection sys- tem. This system automatically cuts off the power to Only for battery cartridges with the indicator extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions: Overload protection This protection works when the tool is operated in a... -
Page 8: Reversing Switch Action
Reversing switch action Displayed Speed Torque Applicable Number operation High Heavy load- ing operation High Light loading operation To change the speed, first switch off the tool and then slide the speed change lever to the "2" side for high speed or, "1" side for low speed. Be sure that the speed change lever is set to the correct position before opera- tion. Use the right speed for your job. -
Page 9: Adjusting The Fastening Torque
Adjusting the fastening torque Installing hook Optional accessory WARNING: Use the hanging/mounting parts for their intended purposes only, e.g., hanging the tool on a tool belt between jobs or work intervals. WARNING: Be careful not to overload the hook as too much force or irregular overburden may cause damages to the tool resulting in personal injury. -
Page 10: Screwdriving Operation
Hammer drilling operation OPERATION CAUTION: There is a tremendous and sud- CAUTION: Always insert the battery cartridge den twisting force exerted on the tool/drill bit all the way until it locks in place. If you can see the at the time of hole breakthrough, when the hole red indicator on the upper side of the button, it is not becomes clogged with chips and particles, or locked completely. -
Page 11: Maintenance
Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attach- ments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885265C229 www.makita.com 20211118...
- Page 13 INSTRUCTION MANUAL Cordless Impact Driver DTD156 Read before use.
- Page 14 SPECIFICATIONS Model: DTD156 Fastening capacities Machine screw M4 - M8 Standard bolt M5 - M14 High tensile bolt M5 - M12 No load speed 0 - 2,500 min Impacts per minute 0 - 3,000 min Overall length 143 mm Rated voltage D.C.
- Page 15 Avoid body contact with earthed or grounded NOTE: The declared vibration total value(s) has been surfaces, such as pipes, radiators, ranges and measured in accordance with a standard test method refrigerators. There is an increased risk of elec- and may be used for comparing one tool with another. tric shock if your body is earthed or grounded. NOTE: The declared vibration total value(s) may also Do not expose power tools to rain or wet con- be used in a preliminary assessment of exposure.
- Page 16 Always wear protective goggles to protect When using the tool, do not wear cloth work your eyes from injury when using power tools. gloves which may be entangled. The entangle- The goggles must comply with ANSI Z87.1 in ment of cloth work gloves in the moving parts may the USA, EN 166 in Europe, or AS/NZS 1336 result in personal injury.
- Page 17 SAVE THESE INSTRUCTIONS. Important safety instructions for battery cartridge CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that Before using battery cartridge, read all instruc- have been altered, may result in the battery bursting tions and cautionary markings on (1) battery causing fires, personal injury and damage. It will charger, (2) battery, and (3) product using also void the Makita warranty for the Makita tool and battery.
-
Page 18: Battery Protection System
Overloaded: FUNCTIONAL The tool is operated in a manner that causes it to draw an abnormally high current. DESCRIPTION In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. CAUTION: Always be sure that the tool is If the tool does not start, the battery is overheated. In... - Page 19 Switch action Reversing switch action ► 1 . Switch trigger ► 1 . Reversing switch lever CAUTION: CAUTION: Before installing the battery car- Always check the direction of tridge into the tool, always check to see that the rotation before operation. switch trigger actuates properly and returns to CAUTION: Use the reversing switch only after...
- Page 20 For tool with shallow driver bit hole NOTE: If the driver bit is not inserted deep enough into the sleeve, the sleeve will not return to its original A=12mm Use only these type of driver position and the driver bit will not be secured. In this B=9mm bit.
- Page 21 To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by 1. Fastening time (second) 2. Fastening torque Makita Authorized or Factory Service Centers, always using Makita replacement parts. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. NOTICE: If you use a spare battery to continue the operation, rest the tool at least 15 min.
- Page 22 OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. • Driver bits • Bit piece •...
- Page 24 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885747-221 www.makita.com 20190801...