Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DHP487YX2B
Summary of Contents for Makita DHP487YX2B
- Page 1 INSTRUCTION MANUAL Cordless Hammer Driver Drill DHP487 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DHP487 Drilling capacities Masonry 13 mm Steel 13 mm Wood Auger bit: 36 mm Self-feed bit: 35 mm Hole saw: 51 mm Fastening capacities Wood screw 6 mm x 75 mm Machine screw No load speed High (2) 0 - 1,700 min Low (1) 0 - 500 min... -
Page 3: Ec Declaration Of Conformity
Save all warnings and instruc- WARNING: Wear ear protection. tions for future reference. WARNING: The noise emission during actual The term "power tool" in the warnings refers to your use of the power tool can differ from the declared mains-operated (corded) power tool or battery-operated value(s) depending on the ways in which the (cordless) power tool. - Page 4 Remove any adjusting key or wrench before Maintain power tools and accessories. Check for turning the power tool on. A wrench or a key left misalignment or binding of moving parts, breakage of parts and any other condition that may affect the attached to a rotating part of the power tool may power tool’s operation.
- Page 5 MISUSE or failure to follow the safety disposal of battery. rules stated in this instruction manual may cause 12. Use the batteries only with the products serious personal injury. specified by Makita. Installing the batteries to non-compliant products may result in a fire, exces- sive heat, explosion, or leak of electrolyte. 5 ENGLISH...
-
Page 6: Tips For Maintaining Maximum Battery Life
Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. Tips for maintaining maximum battery life Charge the battery cartridge before completely discharged. -
Page 7: Overheat Protection
This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service center. NOTE: Depending on the conditions of use and the... -
Page 8: Speed Change
Pull the switch trigger to light up the lamp. The lamp CAUTION: Always set the speed change lever keeps on lighting while the switch trigger is being pulled. fully to the correct position. If you operate the The lamp goes out approximately 10 seconds after tool with the speed change lever positioned halfway releasing the switch trigger. -
Page 9: Installing Hook
Adjusting the fastening torque ► 1 . Action mode changing ring 2. Adjusting ring 3. Graduation 4. Arrow The fastening torque can be adjusted in 20 levels by turning the adjusting ring. Align the graduations with the arrow on the tool body. You can get the minimum fastening torque at 1 and maximum torque at 20. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. -
Page 10: Operation
NOTICE: When hanging the tool on your belt using the hook, remove the driver bit/drill bit. Installing driver bit holder Optional accessory NOTE: When driving wood screw, pre-drill a pilot hole 2/3 the diameter of the screw. It makes driving easier and prevents splitting of the workpiece. -
Page 11: Drilling Operation
The exceptions are iron and brass which To maintain product SAFETY and RELIABILITY, should be drilled dry. repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service CAUTION: Pressing excessively on the tool Centers, always using Makita replacement parts. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885862-221 www.makita.com 20201013...