Table of Contents
Advertisement
N
otes
• Graphics shown in this quick reference guide are for illustration only. Your components may or
may not look exactly the same as drawings shown in this document.
• Refer to Chapter 2 of the User's Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
CPU and Heatsink Installation
Note: For 112L XCC CPU, be sure to use the CPU carrier E1A. For 64L MCC CPU, be sure to use the CPU carrier E1B. You can find the two
CPU carriers in our accessory kit.
Before installation, make sure the lever on the processor carrier is pressed down as shown below. Hold the processor with the LGA lands (gold
1
1
contacts) facing up. Use Pin 1 as a guide to carefully align and place one end of the processor into the latch marked A, and place the other end of
processor into the latch marked B.
Carrier Bottom View
Carrier E1A
(for 112L XCC CPU)
(for 64L MCC CPU)
= Cutout
= Pin 1
= Cutout
= Pin 1
= CPU Key
Hold the processor carrier assembly with the
1
2
gold contacts facing up, then align the holes
of the processor carrier assembly with the
holes on the heatsink. Press the processor
carrier assembly down until it snaps into
place. The plastic clips of the processor
carrier assembly will lock at the four corners.
Align Pin 1 of the PHM with the printed triangle on the CPU socket.
1
3
Make sure all four holes of the heatsink are aligned with the socket,
then gently place the heatsink on top of the CPU socket. Press all four
rotating wires outwards and gradually tighten the four screws to ensure
even pressure.
Examine all corners to ensure that the PHM is firmly attached to the
socket.
Front Control Panel (JF1)
1
Power Button
PWR
Reset Button
Reset
P3V3
UID-LED
P3V3_STBY
P3V3_STBY
P3V3_STBY_UID SW
P3V3
SW_NMI_N
19
20
Carrier E1B
Make sure the lever
is pressed down before
installing the processor.
= CPU Key
Thermal
grease
Back Panel I/O Connectors
1. USB2: USB 2.0 Port
2
2. USB3: USB 2.0 Port
Ground
3. COM1 Port
4. VGA Port
Ground
5. LAN1: RJ45 1GbE LAN Port
Power Fail LED
(Shared IPMI LAN Port)
6. USB8: USB 3.2 Gen. 2x1 Port
OH/Fan Fail LED
7. USB9: USB 3.2 Gen. 2x1 Port
NIC2 Active LED
8. LAN2: RJ45 10GbE LAN Port
NIC1 Active LED
9. USB6: USB 3.2 Gen. 2x1 Port
HDD LED
PWR LED
Ground
Pin 1
A
B
Processor Carrier Assembly
(Upside Down)
Triangle on the CPU
Triangle on the
processor carrier
Airflow direction
(Refer to the airflow
direction arrow on
Airflow direction
the heatsink label to
orient the heatsink.)
Airflow direction
Printed
Triangle
Printed
Triangle
Mount the PHM
onto the CPU socket.
Mount the PHM
onto the CPU socket.
3
5
1
2
6
4
7
Processor Carrier Assembly
Processor Heatsink Module (PHM)
Airflow direction label
Check each corner to ensure
that the processor carrier is
firmly attached to the heatsink.
T30 Torx Screwdriver
Use a torque
of 8 in-lbf
T30 Torx Screwdriver
Use a torque
of 8 in-lbf
Press the rotating wires outwards to
latch the PHM and then tighten the
Press the rotating wires outwards to
four screws.
latch the PHM and then tighten the
four screws.
10. USB7: USB 3.2 Gen. 2x1 Port
11. USB10: USB 3.2 Gen. 2x2 Port
12. Center/LFE Out
13. Surround Out
14. S/PDIF Out
15. Line In
16. Line Out
17. Mic In
18. UID Switch
12
15
8
11
13
16
18
9
10
14
17
Advertisement
Table of Contents
