Advertisement
Quick Links
维修手册
（本图片为参考示意图，具体外观和配置以实物为准）(The picture is only for reference, and
specific appearance and configuration are subject to the real product)
编制
审核
批准
维修手册
Service Manual
适用机型
Applicable Models
FS40-18ARC
Prepared by
Reviewed by
Approved by
Service Manual, 2017 v1.0
马玉剑
张冲
吴孔升
1 / 18
Advertisement
Related Manuals for Midea FS40-18ARC
Summary of Contents for Midea FS40-18ARC
- Page 1 维修手册 Service Manual, 2017 v1.0 维修手册 Service Manual 适用机型 Applicable Models FS40-18ARC （本图片为参考示意图，具体外观和配置以实物为准）(The picture is only for reference, and specific appearance and configuration are subject to the real product) 编制 马玉剑 Prepared by 审核 张冲 Reviewed by 批准 吴孔升 Approved by...
-
Page 2: Important Safety Notice
Midea Environment Appliance Technical Maintenance Manual Copyright @2017 All rights reserved. Replication of all or part of the Manual in any forms shall not be allowed without written approval by the Overseas Sales of Midea Environment Appliance. 2 / 18... -
Page 3: Safety Warning Code
维修手册 Service Manual, 2017 v1.0 安全警示规范 Safety Warning Code WARNING Read these instructions. Keep these instructions. Follow all instructions. Do not use this appliance near water. This appliance is intended to be used in household and similar environments. Clean only with a damp cloth. Install in accordance with the manufacturer’s instructions. - Page 4 维修手册 Service Manual, 2017 v1.0 整机拆卸 Dismantling of appliance The front net cover dismantles to unload 前网罩拆卸 网扣式网罩需要打开网扣再拆下前网罩，部分 网罩需要先拆卸网罩螺钉再拆下前网罩；其他 类型的网罩需要拧松紧固螺钉再拆下前网罩。 The net buttons up type net cover needs to open a net to button up again dismantle front net cover, parts of net covers need to dismantle first to unload a net cover bolt again the net cover before...
- Page 5 维修手册 Service Manual, 2017 v1.0 The fuselage dismantles to unload 机身的拆卸 使用螺丝刀将扇盒后壳底部的螺丝拧松，然后 向上取下机身 Use screw knife the screw Ning of hull bottom is loose, then dismantle a fuselage upward after the box Take out dismantling of knob to unload 2.5抽钮的拆卸 如果抽钮内无螺钉可直接向上用力拔出抽钮，...
- Page 6 维修手册 Service Manual, 2017 v1.0 then dismantles electrical engineering before the hull and the electrical engineering after the electrical engineering after hull The hull dismantles to unload before the electrical 电机前壳的拆卸 用螺丝刀取下电机前壳中间的四颗或两颗螺 钉，即可取下电机前壳 With the screw knife dismantle hull middle before electrical engineering of four or two bolts, can...
- Page 7 维修手册 Service Manual, 2017 v1.0 The electric wire dismantles to unload 电线的拆卸 可用指尖或回形针等插入线孔，撬动琴键的卡 紧触片，取下接线 Can insert line bore with the finger tip or time form needle etc., pry the card of keyboard to tightly touch a slice, dismantle to connect line The electrical engineering dismantles to unload 电机的拆卸...
- Page 8 维修手册 Service Manual, 2017 v1.0 The conjunction head dismantles to unload 连接头的拆卸 2.11 将扇盒顶端的螺钉拆卸出来后即可取出连接 头 Dismantle the bolt of box top can immediately take out to connect to deal with contact after unloading out 部分连接头型号具有防拆卸结构，需要用螺丝 刀将扇盒顶部略微撬开才能拆卸连接头 Parts of conjunction head model numbers have to defend to dismantle to unload structure, need to use screw knife box coping's just...
- Page 9 维修手册 Service Manual, 2017 v1.0 整机的安装 Function and operation 连接头的安装 Operation panel 将电机机头线穿过连接头，将电机中心轴插 入连接头定位套孔中，将定位钉拧紧在连接 头上，并测试电机是否已经固定在连接头上 Electrical engineering machine head line once wore conjunction head and inserted the electrical engineering central axis into the conjunction head fixed position set bore in, nail fixed position to Ning tightly on the conjunction head, and test if the electrical engineering has already...
- Page 10 维修手册 Service Manual, 2017 v1.0 电机后壳的安装 Display screen 将电机后壳从电机后部套入电机，对好电机 前壳后插入前壳中，扣位连接的需要确保 4 个扣位扣紧，螺钉连接的需要使用螺钉将电 机后壳固定 Make hull going into electrical engineering after the electrical engineering from the department set after the electrical engineering, to before the good electrical engineering the hull is behind before inserting hull in, buttonned up needing of a conjunction to ensure 4 to button up and tie tight,...
- Page 11 维修手册 Service Manual, 2017 v1.0 开关的安装 Setting of the gear 使用扣位将开关安装到扇盒前壳上 Use bolt or button up switch and machine's installing box is in the ex- hull 电线的安装 Super cool 按照接线图，将各档位线、电源线连接在开 关上，有地线的还需要连接地线 According to connecting line diagram, each file line the machine line, power cable link at the switch machine up, there is still needing of a ground of line linking a ground of...
- Page 12 维修手册 Service Manual, 2017 v1.0 底盘的安装 Super cool 使用七字螺栓、索母、蝶形螺母将底盘与立 柱管连接， 或使用螺钉将底盘及立柱管连接， 并装好装饰盖 Use seven word stud bolts and Suo mother and Die form Luo mother bedrock with sign a pillar tube conjunction, or use bolt bedrock and sign a pillar tube to link, and pack to decorate a cover so much 机身的安装...
- Page 13 维修手册 Service Manual, 2017 v1.0 hull combine to the good, use a net cover Suo the mother is tightly solid, parts of net covers downwards install in wearing to conduct electricity crankshaft after covering net from, and follow hour hand Ning to move a knob to fix 风叶的安装...
- Page 14 维修手册 Service Manual, 2017 v1.0 ability 处理方法： 检查插座是否有电， 如出现故障更换。 normal 可能原因 2： start B、产品内部各部分故障： B1、 定时器是否置 “零” ， 即旋钮是否置到 “开” 的位置上； B2、电路板故障：接线出现松脱，接触不良引 起内部线断开； B2、内部接线故障：内部线断、插线没有插好 （压到胶皮）； B3、电机故障：烧坏或热熔断器断路。 处理方法： 分段检查， 逐一排除找到原因后进行修理。 Possible reason 1: The AC outlet of A, family breaks down. Treatment:Check whether the electric outlet contains electricity, if appear to break down to replace.
- Page 15 维修手册 Service Manual, 2017 v1.0 head not 头（卡死） 可能原因： fluently A、电源不稳定，引起电机转速时快时慢，造成 疾步。 B、内部四连杆机构异常现象： B1、不摇头： 齿箱故障：齿轮断齿；齿箱卡死。 曲柄断。 螺丝松开。 螺丝压死连杆，连杆不能转动。 B2、疾步：齿箱输出轴晃动、连杆变形，螺丝 松动。 B3、其它原因。 处理方法：以上不良，需拆开机头部分，进行检修， 根据可能原因逐一排除找到原因后进行修理。 Bad phenomenon:The slow disease tread(is unsteady) and doesn't shake head while being quick while shaking head(choked to death) Possible reason: While being quick when AN and the power was unsteady, aroused electrical...
- Page 16 维修手册 Service Manual, 2017 v1.0 transform, screw loose move. B3, other reason. Treatment:Is above bad, need to tear open machine head for cent, carry on check to fix, one by one expel to find out reason juniors a line to fix according to the possible reason.
- Page 17 平口螺丝刀/小铲刀 拆卸螺钉和铆钉 screw and slotted screwdriver/scraper rivet assemble and disassemble 拆卸铰链、压缩机螺钉 hinge 套筒扳手 Socket spanner and compressor screw assemble 5/16″ and disassemble 尖嘴钳 辅助工具 Nipper pliers assistive tool 美的环境电器 如需获得厂家详细技术咨询，请联系： xxx@midea.com 环境电器事业部 外销 地址：中国广东省中山市东凤镇东阜路和穗工业园东区 28 号 17 / 18...
- Page 18 维修手册 Service Manual, 2017 v1.0 Midea Environment Appliance If you need to get detailed technical information from the manufacturer, please contact: xxx@midea.com Environment Appliance Division Overseas Sales Address: Eastern 28th, Hesui industrial Park, Dongfu Road, Dongfeng Town, Zhongshan City, Guangdong Province China...