Download Print this page
iOptron CEM40-UNC Quick Start Manual

iOptron CEM40-UNC Quick Start Manual

Center-balanced goto equatorial mount

Advertisement

Quick Links

Quick Start Guide
CEM40™ Center-balanced GoTo Equatorial Mount
Model: CEM40, CEM40G, CEM40EC & CEM40-UNC (#C40XXX Series)
1
PACKAGE CONTENTS
 CEM40 mount with internal iPolar
 Go2Nova® Hand Controller (HC)
 Counterweight – 11 lbs (5 kg, #8027)
 Stainless steel counterweight shaft
 GPS module
 RJ11 coiled cables, x2
 USB cable
 AC adapter – 100-240V (DC output 12V/5A) with 2.5/5.5mm DC plug
 Alignment peg (located in mount head package)
 1.5" or LiteRoc
TM
heavy duty tripod and accessory tray
 Optional hard case
 Quick Start Guide (this document)
ONLINE RESOURCES (at www.iOptron.com, under Support)
 User's Manual
 Hand controller and mount firmware upgrades (check online for the latest version)
 ASCOM and Commander for computer control
Ver 3.0 Nov. 2022
1
The design, contents and packaging may change from time to time without notice.
iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA |
TM
electronic Polar Scope
Support@iOptron.com
| www.iOptron.com
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the CEM40-UNC and is the answer not in the manual?

Questions and answers

Summary of Contents for iOptron CEM40-UNC

  • Page 1  Hand controller and mount firmware upgrades (check online for the latest version)  ASCOM and Commander for computer control Ver 3.0 Nov. 2022 The design, contents and packaging may change from time to time without notice. iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 2 Locking Knob from Adjustment Knob to set the correct latitude value, as underneath. displayed in the Latitude Mark Window. Insert the iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 3 Unthread and remove the Position Bolt to its new Vixen or a Losmandy-D plate. The CEM40AG has an location. Adjust the Latitude Adjustment Knob while iGuider guiding system on the dovetail saddle. iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 4  Connect a USB cable between the USB2.0 port on the rear end of the mount RA axle and a computer USB port iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 5 Set Zero Position: The Set Zero Position command registers the current position as zero position. So before registering, the mount should be physically set iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 6 V2.0 iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | Support@iOptron.com | www.iOptron.com...
  • Page 7: Ioptron Two Year Telescope, Mount, And Controller Warranty

    A. iOptron warrants your telescope, mount, or controller to be free from defects in materials and workmanship for two years. iOptron will repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workmanship. As a condition to the obligation of iOptron to repair or replace such product, the product must be returned to iOptron together with proof-of- purchase satisfactory to iOptron.

This manual is also suitable for:

Cem40Cem40gCem40ecC40 series