Advertisement
Quick Links
Quick Start Guide
CEM40™ Center‐Balanced GoTo Equatorial Mount
Models: #7400A (CEM40) , #7400ECA (CEM40EC)
1
PACKAGE CONTENTS
Telescope mount – with iPolar
Hand controller (HC) – Go2Nova® 8407+
Counterweight – 10 lbs X1 (4.5 kg)
Stainless steel counterweight shaft
GPS module
RJ11 coiled cable X2
RS232‐RJ9 serial cable
USB cable
AC adapter – 100‐240V (DC output 12V/5A)
Alignment peg (located in mount package)
1.5" tripod and accessory tray (tray located in mount package)
Hard case (for 7400ECA, optional for 7400A)
Quick Start Guide (this document)
ONLINE RESOURCES (at www.iOptron.com, under "Support")
User's Manual
Hand controller and mount firmware upgrades (check online for the latest version)
ASCOM and Commander for computer control
1
The design, contents and packaging may change from time to time without notice.
TM
electronic Polar Scope
iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for iOptron 7400A
Summary of Contents for iOptron 7400A
- Page 1 RJ11 coiled cable X2 RS232‐RJ9 serial cable USB cable AC adapter – 100‐240V (DC output 12V/5A) Alignment peg (located in mount package) 1.5” tripod and accessory tray (tray located in mount package) Hard case (for 7400ECA, optional for 7400A) Quick Start Guide (this document) ONLINE RESOURCES (at www.iOptron.com, under “Support”) User’s Manual Hand controller and mount firmware upgrades (check online for the latest version) ASCOM and Commander for computer control The design, contents and packaging may change from time to time without notice. iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com ...
- Page 2 Adjustment Knobs to allow enough clearance inside the chamber for alignment peg. Position the mount on the tripod head with the Alignment Peg in Lat. Adj. Knob between the 2 Azimuth Adjustment Knobs. Remove iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com ...
- Page 3 Vixen or Losmandy‐D plate by flipping both locking shaft mounting house. sides. The center of the dovetail saddle can be adjusted to ensure that the scope is at the center of For low latitude (<10°), a special CW mounting house the dovetail saddle. is needed. The following pictures show how to change the dovetail saddle from Vixen to Losmandy. iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com ...
- Page 4 Polar Alignment: CEM40 & CEM40EC are equipped equipment damage. with an iPolar electronic polar scope. To perform polar alignment, please refer to CEM40 full iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com ...
- Page 5 Position at the end of the observing session. Lay the Sydney is “UTC +600 minutes” mount into the carrying case. Disengage the gear system for transportation. Waiting for the mount to pick up the GPS (you’ll hear beep). If the GPS OKed during setup, just power cycle Please contact support@ioptron.com for technical the mount. Double check the HC display and it should support. show correct local time. iOptron Corp. | 6E Gill Street | Woburn, MA 01801 USA | (781) 569-0200 | www.iOptron.com ...
-
Page 6: Ioptron Two Year Telescope, Mount, And Controller Warranty
A. iOptron warrants your telescope, mount, or controller to be free from defects in materials and workmanship for two years. iOptron will repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workmanship. As a condition to the obligation of iOptron to repair or replace such product, the product must be returned to iOptron together with proof-of- purchase satisfactory to iOptron.
Need help?
Do you have a question about the 7400A and is the answer not in the manual?
Questions and answers