National Instruments PXIe-4464 Getting Started Manual
204.8 ks/s, 119 db, 6 gains, ac/dc-coupled, 4 input pxi sound and vibration module
Hide thumbs
Also See for PXIe-4464:
- Calibration procedure (19 pages) ,
- Getting started manual (8 pages)
Table of Contents
Advertisement
Quick Links
GETTING STARTED GUIDE
PXIe-4464
204.8 kS/s, 119 dB, 6 Gains, AC/DC-Coupled, 4-Input PXI Sound and
Vibration Module
This document explains how to install, configure, and set up the PXIe-4464 Sound and Vibration
Module. Driver support for the PXIe-4464 was first available in NI-DAQmx 14.1. For the list of
devices supported by a specific release, refer to the NI-DAQmx Readme, available on the
version-specific download page or installation media. To download NI-DAQmx 14.1, visit
and enter the Info Code
. The PXIe-4464 is available with BNC
ni.com/info
PXIE4464
connectors or Mini-XLR connectors.
Contents
Electromagnetic Compatibility Guidelines .............................................................................. 1
Unpacking the Kit..................................................................................................................... 2
Preparing the Environment ....................................................................................................... 3
Verify the Kit Contents............................................................................................................. 3
Other Equipment....................................................................................................................... 3
Install the Software ................................................................................................................... 4
Install the Hardware.................................................................................................................. 4
Configuring the PXIe-4464 in MAX........................................................................................ 7
Connect a Signal Source to the PXIe-4464 .............................................................................. 8
Environmental Management..................................................................................................... 11
Worldwide Support and Services ............................................................................................. 11
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with radio
and television reception and prevent unacceptable performance degradation, install and use this
product in strict accordance with the instructions in the product documentation.
Furthermore, any modifications to the product not expressly approved by National Instruments
could void your authority to operate it under your local regulatory rules.
Advertisement
Table of Contents
Related Manuals for National Instruments PXIe-4464
Summary of Contents for National Instruments PXIe-4464
-
Page 1: Table Of Contents
This document explains how to install, configure, and set up the PXIe-4464 Sound and Vibration Module. Driver support for the PXIe-4464 was first available in NI-DAQmx 14.1. For the list of devices supported by a specific release, refer to the NI-DAQmx Readme, available on the version-specific download page or installation media. -
Page 2: Unpacking The Kit
(HI). However, for functional reasons, there is no input configuration of the PXIe-4464 that directly connects the LO terminal to the chassis ground. Without a direct connection to chassis ground, the outer conductor does not act as a shield for unwanted noise and may act as an antenna for coupling noise into the module inputs. -
Page 3: Preparing The Environment
Preparing the Environment Ensure that the environment you are using the PXIe-4464 in meets the following specifications. Operating ambient temperature ......0 °C to 55 °C (IEC 60068-2-1, IEC 60068-2-2) Operating relative humidity......10% to 90%, noncondensing (IEC 60068-2-56) Altitude ............. 2,000 m (800 mbar) (at 25 °C ambient temperature) -
Page 4: Install The Software
Install the Software Software support for the PXIe-4464 is provided by NI-DAQmx. The DAQ Getting Started Guide, which you can download at , offers step-by-step NI-DAQmx ni.com/manuals instructions for installing software and hardware, configuring channels and tasks, and getting started developing an application. For detailed NI software version support, refer to the NI-DAQmx Readme. - Page 5 Remove the black plastic connectors from all the captive screws on the module front panel. Identify a supported slot in the chassis. The PXIe-4464 module can be placed only in the supported slot types identified in Table 1. Figure 1 shows the slot type symbols of the various slot types.
- Page 6 Place the module edges into the module guides at the top and bottom of the chassis. Slide the module into the slot until it is fully inserted. Figure 2. Sliding the PXIe-4464 into the Chassis Chassis Injector/Ejector Handle in Down (Unlatched) Position Hardware Module (BNC model shown) Latch the module in place by pulling up on the ejector handle.
-
Page 7: Configuring The Pxie-4464 In Max
In the Configuration pane, expand Devices and Interfaces to see a list of installed devices. Installed devices appear under the name of their associated chassis. If you are using the PXIe-4464 with the LabVIEW Real-Time Module, Note expand Remote Systems. Find your target IP address or name, expand it, and then expand Devices and Interfaces. -
Page 8: Connect A Signal Source To The Pxie-4464
Connect a Signal Source to the PXIe-4464 The following figure shows the front panel connections of the PXIe-4464 with BNC connectors and the PXIe-4464 with Mini-XLR connectors. Refer to the PXIe-4464 Specifications for information about the operating Note input range and overvoltage protection. - Page 9 Figure 4. PXIe-4464 Input Connection in Differential Mode 217 pF 1 MΩ – – 223 pF 1 MΩ The following figure shows an PXIe-4464 input connection with the terminal configuration in pseudodifferential mode. Figure 5. PXIe-4464 Input Connection in Pseudodifferential Mode 217 pF 1 MΩ – –...
- Page 10 The following figure shows the PXIe-4464 analog input circuitry block diagram. Depending on the connector type, connect the signals as shown in the inset. Figure 6. PXIe-4464 Analog Input Block Diagram 25 V Compliant IEPE Constant Current Source 4/10/20 mA...
-
Page 11: Environmental Management
NI. National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also has offices located around the world. For telephone support in the United States, create your service request at or dial ni.com/support... - Page 12 NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.