National Instruments PXIe-4339 Installation Manual

National Instruments PXIe-4339 Installation Manual

8 ch, 24-bit, 25.6 ks/s universal bridge input module
Hide thumbs Also See for PXIe-4339:

Advertisement

INSTALLATION GUIDE AND TERMINAL BLOCK
SPECIFICATIONS
NI PXIe-4339 and TB-4339/B/C
8 Ch, 24-bit, 25.6 kS/s Universal Bridge Input Module
This document explains how to install, configure, and set up the NI PXIe-4339 SC Express
universal bridge module and TB-4339/4339B/4339C (TB-4339/B/C) terminal block. Driver
support for the NI PXIe-4339 was first available in NI-DAQmx 14.2. For the list of devices
supported by a specific release, refer to the NI-DAQmx Readme, available on the
version-specific download page or installation media.
The keying of these terminal blocks prevents them from connecting to other
Note
modules that could be damaged by the voltage present on the terminal block.
However, you should only use these terminal blocks with their supported modules.
Contents
Electromagnetic Compatibility Guidelines .............................................................................. 2
What You Need to Get Started ................................................................................................. 2
Installation ................................................................................................................................ 3
Install the Software ........................................................................................................... 3
Unpack and Install the Module......................................................................................... 3
Connect the Signals .......................................................................................................... 5
Install the Terminal Block ................................................................................................ 8
Confirm SC Express Module Recognition ....................................................................... 9
Run Test Panels ................................................................................................................ 10
Take an NI-DAQmx Measurement .................................................................................. 11
NI-DAQmx Channels and Tasks.............................................................................. 11
Configure a Task Using the DAQ Assistant in MAX .............................................. 11
Use Your SC Express Module in an Application ............................................................. 12
Programming Examples ........................................................................................... 12
Terminal Block Removal.......................................................................................................... 12
Module Removal ...................................................................................................................... 13
Create a Simulated Device ....................................................................................................... 14
More Information ..................................................................................................................... 15
Troubleshooting................................................................................................................ 15
Specifications (TB-4339/B/C) .................................................................................................. 15
Calibration Interval................................................................................................................... 15

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PXIe-4339 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for National Instruments PXIe-4339

  • Page 1: Table Of Contents

    This document explains how to install, configure, and set up the NI PXIe-4339 SC Express universal bridge module and TB-4339/4339B/4339C (TB-4339/B/C) terminal block. Driver support for the NI PXIe-4339 was first available in NI-DAQmx 14.2. For the list of devices supported by a specific release, refer to the NI-DAQmx Readme, available on the version-specific download page or installation media.
  • Page 2: Electromagnetic Compatibility Guidelines

    PFI0/DGND, and T+/DGND that is cabled. Cable shields must be terminated to chassis ground at both ends. What You Need to Get Started To set up and use a NI PXIe-4339 module with a TB-4339/B/C terminal block, you need the following items: ...
  • Page 3: Installation

    Remove the packaging and inspect the module. Contact NI if the module is damaged. Do not install a damaged module. The module is static sensitive. Always properly ground yourself and the Caution equipment when handling or connecting to the module. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 3...
  • Page 4 To maintain forced air cooling in the PXIe system, refer to the Maintain Note Forced-Air Cooling Note to Users. Plug in your chassis before installing the NI PXIe-4339. The power cord grounds the chassis and protects it from electrical damage while you install the module. Make sure the chassis is powered off.
  • Page 5: Connect The Signals

    Loosen the strain-relief screws and remove the strain-relief bar. Prepare the shielded signal wire by stripping the insulation no more than 7 mm (0.28 in.). Run the shielded signal wires through the strain-relief opening. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 5...
  • Page 6 The NI PXIe-4339 User Manual provides more detailed wiring information. Make sure no exposed wire extends past the screw terminal. Exposed wire increases the risk of a short circuit that can cause circuit failure.
  • Page 7 Use tie wraps to connect the shielded signal wires to the tie-wrap holes for additional strain relief when necessary. 10. Reinstall the top cover and tighten the captive top cover screws. For information about sensors, go to Note ni.com/sensors NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 7...
  • Page 8: Install The Terminal Block

    Attach the TB-4339/B/C to the NI PXIe-4339 module by pushing the terminal block straight into the module. A spring mechanism will lock in the bottom of the terminal block. Tighten the mounting screw at the top of the TB-4339/B/C to attach it to the NI PXIe-4339 module.
  • Page 9: Confirm Sc Express Module Recognition

    If your module or terminal block is not listed, press <F5> to refresh MAX. If the module is still not recognized, go to ni.com/support/ daqmx NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 9...
  • Page 10: Run Test Panels

    For information about sensors, go to ni.com/sensors Run Test Panels In MAX, expand Devices and Interfaces select the chassis in which the module is located. Right-click the device, and select Test Panels. 10 | ni.com | NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications...
  • Page 11: Take An Ni-Daqmx Measurement

    To modify the input range or other settings, select the channel. Click Details for physical channel information. Configure the timing and triggering for your task. Click Run. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 11...
  • Page 12: Use Your Sc Express Module In An Application

    The chassis can be powered on or off when removing the terminal block. Note Loosen the terminal block mounting screw located at the top of the terminal block. 12 | ni.com | NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications...
  • Page 13: Module Removal

    Forced-Air Cooling Note to Users. Make sure that the chassis is powered off before removing the module. Loosen the captive screws on the top and bottom of the module. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 13...
  • Page 14: Create A Simulated Device

    From the dialog, select Simulated NI-DAQmx Device or Modular Instrument. Type in the text box at the top of the window. 4339 Select the device from the list provided. Click OK. 14 | ni.com | NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications...
  • Page 15: More Information

    Quarter bridge completion... 1 kΩ ±0.1%, ±10 ppm/°C Shunt calibration resistor ..... 100 kΩ ±0.1%, ±10 ppm/°C Trace resistance (screw terminal to connector) EX+, EX- ............<20 mΩ NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 15...
  • Page 16: Mechanical

    IEC 60068-2-2. Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 2 high temperature limit.) Relative humidity range........10% to 90%, noncondensing (Tested in accordance with IEC 60068-2-56.) 16 | ni.com | NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications...
  • Page 17: Storage Environment

    Measurement Categories CAT I and CAT O are equivalent. These test and measurement circuits are not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT IV. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 17...
  • Page 18: Electromagnetic Compatibility

    To obtain product certifications and the DoC for this product, visit ni.com/ , search by model number or product line, and click the appropriate link in the certification Certification column. 18 | ni.com | NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications...
  • Page 19: Environmental Management

    1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the Worldwide Offices section of to access the branch office websites, which ni.com/niglobal provide up-to-date contact information, support phone numbers, email addresses, and current events. NI PXIe-4339/TB-4339 Installation Guide and Terminal Block Specifications | © National Instruments | 19...
  • Page 20 NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.

This manual is also suitable for:

Tb-4339Tb-4339bTb-4339c

Table of Contents