Advertisement
Device Installation/ 设备安装
A. SD Card Installation/ 安装 SD 卡
Use the Phillips screwdriver to remove the camera bottom cover, and insert the SD card. You can refer to the SD
card icon on the maintenance window for the insertion direction. During SD card installation, you are advised to
turn the camera maintenance window downward and insert the SD card into the SD card slot from below to avoid
accidentally dropping the SD card into the camera.
使用十字螺丝刀将摄像机底盖卸下，插入 SD 卡，SD 卡插入方向参考维护窗上标识。安装 SD 卡时，建议将摄像机维护窗朝下，
避免不慎将 SD 卡掉入摄像机内部，造成设备故障。
CAUTION/ 注意
When the camera is not or cannot be connected to a video surveillance platform for a long time, you are advised to disable
video buffering to increase the service life of the SD card.
Do not remove the protective film from the lens before the installation is complete.
若摄像机长时间无法接通平台或者不对接平台使用，建议手动关闭摄像机的平台离线缓存补录功能，以提高SD卡的使用寿
命。
安装完成前切勿撕下镜头保护膜。
Unfasten the three hose clamps and thread them through the installation holes on the pole-mount bracket.
2
Place the hose clamps around the beam and tighten them to affix the pole-mount bracket firmly onto the
beam.
将 3 个喉箍拧开，穿过抱装支架的安装孔。将喉箍环绕在横臂上，拧紧喉箍，将抱装支架固定在横臂上。
B. Beam-mounted Installation (Without Junction Box)/ 横臂 （不带接线盒）
Thread the camera pigtails through the center of the mounting bracket, and connect the external cabling.
1
Insulate and waterproof the connections (see Cable Connections, at the end of this section), fix the pigtails in
place, and use the M4 screws to fasten the camera to the mounting bracket using the number 5 holes.
将摄像机尾线穿过柱装支架中心圆孔， 将线缆与尾线连接， 对线缆进行绝缘和防水处理 （参见 "连接线缆" ） ， 并固定尾线。
选择编号为 5 的螺口，拧紧 M4 螺钉。
CAUTION/ 注意
Make sure the cable outlet (marked with BOTTOM) faces downwards or water may enter the camera and damage the
device.
摄像机底座写有BOTTOM字样的出线口朝向下方，防止水流入到摄像机内部，造成摄像机故障。
Loosen the three hex socket bolts and adjust the camera to the required angle. Then, re-tighten the bolts and
3
adjust the position of the sunshield.
拧松支架的 3
个内六角螺钉，调整摄像机监控角度至所需位置，再拧紧内六角螺钉。同时调整好遮阳板位置。
NOTE/ 说明
After adjusting the angle of the camera, if you are unable to automatically or manually bring the image
into focus, log in to the IPC web client, and click the
调整完毕后，在自动对焦或者手动聚焦后图像仍然模糊（由镜头失步引起的虚焦），请登录Web页面，在预览界
面，单击页面云台控制面板的复位镜头
3
icon on the PTZ control panel to reset the lens.
。
Advertisement
