Advertisement
Interface Description/ 接口说明
1
DC12V-
2
AC24V~
DC12V+
AC24V~
3
4
5
6
7
NO.
Item
Description
序号
名称
说明
Ethernet/PoE connection. This interface supports PoE.
1
PoE/LAN
网络接口，该接口支持PoE供电。
Power input interface. (12 V ±25% DC, 24 V AC -25% to +24.9%)
2
POWER
电源输入接口。支持DC12V (±25%)，AC24V (-25%~+24.9%)电源输入。
Analog video output interface. This interface is used only for troubleshooting video output.
3
VIDEO
模拟视频输出接口，仅用于调试视频输出。
ALARM_OUT
Alarm output and reference interfaces. The interfaces work together to form the alarm output.
告警输出接口。ALARM OUT和ALARM REF组成一组告警输出。
ALARM_REF
Alarm input interface. There may be multiple alarm interfaces. For a given number of
interfaces, n, they are numbered (for example: ALARM_IN0, ALARM_IN1, ..., ALARM_INn). Each
4
ALARM_IN
one connects to the GND connection to form a single alarm input.
告警输入接口。存在多个告警输入线，则采用ALARM_INn表示，n为数字，每条告警线与GND组成一
组告警输入。
Alarm input ground interface.
GND
告警输入接地接口。
AUDIO IN/
Audio input/output interface and audio ground interface.
5
AUDIO OUT/
AUDIO IN/AUDIO OUT为音频输入/输出接口。GND为音频接地接口。
GND
RS485 interface. This interface provides a transparent data channel for half-duplex
RS485+/
6
transmission between the camera and the connected device.
RS485-
RS485接口。通过该接口，摄像机可以以半双工的方式通过透明通道与连接的设备互相传递数据。
Ground interface of an IPC.
7
GND
设备接地接口。
Required Tools/ 准备安装工具
Hammer drill (for ceiling- or
Video surveillance tester
wall-mounted installations)
视频监控测试仪
冲击钻（吊顶和墙壁安装时使用）
Measuring tape
Wire stripper
钢卷尺
The color identifier of the
alarm cable is subject to
the actual pigtail label.
告警线缆颜色标识以实际的尾
线标签为准。
PVC insulation tape
绝缘胶带
Waterproof tape
剥线钳
防水胶带
Reset Button and SD Card Slot/Reset 键和 SD 卡槽
3
1
NOTE/ 说明
2
1
2
NO.
Description
序号
说明
Reset button. To restart the device, hold down the reset button (less than 3s). To restore the
device to factory settings, hold down the reset button for at least 3s while the device running,
Reset button
or hold down the reset button while powering on the device, and keep the button pressed for
1
重置键
more than 5 seconds.
运行时按住Reset键短于3秒重启设备；运行时按住Reset键不短于3秒或者按住Reset键后上电并持续按
住Reset键不短于5秒后恢复出厂配置。
SD card slot. The SD card slot supports only class 10 or higher Micro SD cards. To replace a
Micro SD card, the device must be powered off. Otherwise, system exception may occur. When
SD card slot
a Micro SD card is used for the first time, log in to the web client of the device and format the
2
SD卡卡槽
Micro SD card. For details, see the Configuration Guide.
SD卡卡槽，支持Micro SD卡（Class 10及以上）。请在设备断电的情况下插拔SD卡，否则可能会造成
系统异常。首次使用时，请登录设备Web客户端，格式化SD卡，操作方法请参见《配置指南》。
Off: The device is powered off.
灯灭：设备未上电；
Orange: The system is starting.
橙色：系统正在启动；
Green: The system is running properly.
Status
绿色：系统运行正常；
indicator
系 统 运 行 状 态
3
Steady red: The hardware is faulty.
指示灯
红色长亮：硬件产生故障；
Fast flashing red: The device temperature is outside of its acceptable operating range and an
alarm has been generated.
红色快闪：高温低温到达阈值，产生温度告警；
Slow flashing red: Packet loss occurs on the network port or the optical port is abnormal.
红色慢闪：网口丢包、光口异常。
Hammer (for ceiling- or wall-
mounted installations)
RJ-45 connector crimping tool
羊角锤（吊顶和墙壁安装时使用）
Utility knife
裁纸刀
2
3
Phillips screwdrivers (1# and 2#)
水晶头压线钳
十字螺丝刀（1#和2#）
Wrench
Wiring terminals
扳手
接线端子
NOTE/ 说明
Use the Phillips screwdriver
to remove the camera
bottom cover. Then, you
can see the Reset button,
SD card slot and system
running status indicator.
使用十字螺丝刀将摄像机底盖
卸下，即可看到重置键、SD
卡槽和系统运行指示灯。
Diagonal cutting pliers
斜口钳
Cable ties
扎线带
Advertisement
