Summary of Contents for Hearth & Home PRIMO-II Series
Page 1
Traditional Logs, Driftwood Logs, Birch Logs OAKLG-LIN-SM/LG, DWLG-LIN-SM/LG, BIRLG-LIN-SM/LG Model: PRIMO-II Series Leave this manual with party responsible for use and operation. CAUTION: Logs are fragile, handle with care. NOTICE: To simplify the installation process, positively identify each individual log before beginning installation.
Page 2
Preparation: Install log locating pins, included in hardware bag, into all locations as shown in the figures below. Extra log pins are included in manual bag. Log pins are identified alphabetically as shown below. Log pin holes are circular in shape, with the exception of a few rectangular holes, which are shaded in Figures 2A, 2B and 2C.
Page 3
Log Installation: OAKLG-LIN-SM / DWLG-LIN-SM / BIRLG-LIN-SM Models: PRIMO-II-48, PRIMO-II-48ST Log #10: Place Log #10 in back left of firebox using log pins (A) and (B) for positive placement. Place the right side of Log #10 against log pin (B) and then pivot the left side of Log #10 back to meet log pin (A). See Figure 1. Log #3: Place the left side of Log #3 against log pin (C) and pivot the right side of Log #3 back to meet log pin D.
Page 4
Log #6: Insert the left side support feature of Log #6 into the recess on Log #5. Pivot the right side of the log forward as far as it can go. Ensure the log is stable and fully engaged with Log #5, the supporting log. See Figure 7. Log #1: Place the end of Log #1 against log pins (G) and (H) in the back right corner of the firebox.
Page 5
Log Installation: OAKLG-LIN-LG / DWLG-LIN-LG / BIRLG-LIN-LG Models: PRIMO-II-60, PRIMO-II-60ST Log #1: Center the log left to right between the log pins noted in Figure 1. Slide Log #1 back until it contacts both log pins. See Figure 2. Figure 1 Log Pins for Log #1 Figure 2 Install Log #1 Log #3: Place the left side of Log #3 against log pin (C).
Page 6
Log #4: Place Log #4 against the right log pin (K). Pivot the log backward until it contacts the left log pin (J). See Figure 7. Log #7: Set the right side of Log #7 on Log #4 as shown in Figure 8. There should be a 1-1/2 inch overlap as noted. Pivot the left side of the log forward until it contacts the media tray ledge.
Page 7
Log Installation: OAKLG-LIN-LG / DWLG-LIN-LG / BIRLG-LIN-LG Models: PRIMO-II-72, PRIMO-II-72ST Log #1: Center Log #1 left to right between log pins (A) and (B) as shown in Figure 1 and Figure 2. Slide Log #1 back until it contacts both log pins. Figure 1 Log Pins for Log #1 Figure 2 Install Log #1 Log #3: Place the left side of Log #3 against log pin (C).
Page 8
Log #4: Place Log #4 against log pin K on the right shown in Figure 7 and Figure 8. Pivot the log backward until it contacts the left log pin (J). See Figure 7. Log #6: Insert the left side support feature of Log #6 into the recess on Log #5. Pivot the right side of the log forward until it contacts the media tray ledge.
Troubleshooting If flames impinge upon the logs after installation, minor shifting of log position or media may be necessary to reduce flame impingement and sooting. Log Sets Installed Log Set Installed - PRIMO-II-48 OAK LOGS Log Set Installed - PRIMO-II-60 OAK LOGS Log Set Installed - PRIMO-II-48 DRIFTWOOD Log Set Installed - PRIMO-II-60 DRIFTWOOD Log Set Installed -PRIMO-II-60 BIRCH...
Log Set Installed - PRIMO-II-72 DRIFTWOOD Log Set Installed - PRIMO-II-72 BIRCH Service Parts List HHT Part # Model Description All Log Sets 501-836-25 PRIMO-II Series Log Pin (Quantity 25) HHT Part # Model Description OAKLG-LIN-SM PRIMO-II-48/ST Oak Linear Log Set - Small...
Need help?
Do you have a question about the PRIMO-II Series and is the answer not in the manual?
Questions and answers