Table of Contents
Advertisement
• Important operating
a n d m a i n t e n a n c e
instructions included.
1
Introduction
Table of Contents
1 Introduction
A. Components and Service Parts List . . . . . . . . . . . . . . . . . . 2
B. Installation of PVLP-SLP . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Vent Information and Diagrams
A. Installation of Vent Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
►
B. Vent/Pipe Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C. Venting Length - Model Categories and Length
►
Requirements by Termination Type . . . . . . . . . . . . . . . . . 9
3 Framing and Clearances
A. Framing and Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . 10
B. Installing Vent Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 Electrical Information
A. Wiring the Appliance for the PVLP-SLP with IntelliFire™ Plus
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Wiring the Appliance for the PVLP-SLP with IntelliFire™ Touch
(IFT) Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
C. Pairing the IFT-RC400 to the Electronic Control Electronic
Control module (IFT-ECM) . . . . . . . . . . . . . . . . . . . . . . . . 26
5 Operating Instructions
A. Installation Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
B. Setting the PVLP-SLP Baffle Adjustment . . . . . . . . . . . . . 27
C. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
D. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
E. Replace Blower/Pressure Switch . . . . . . . . . . . . . . . . . . . 29
F. PVLP-SLP Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 30
G. IFT-Controls and PVI-SLP Power Vent Troubleshooting . .31
H. Addendum: Signature Command Fireplaces. . . . . . . . . . . 32
1
Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17
PVLP-SLP
Power Vent Low Profile
- Installation Instructions -
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
Installation of the PVLP-SLP may be done by a quali-
fied service technician only. Installation MUST com-
ply with local, regional, state and national codes and
regulations.
IMPORTANT:
Failure to read and follow these instruc-
tions may create a possible hazard and will void the fire-
place warranty.
These instructions must remain with the equipment.
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
INTRODUCTION
The Power Vent Low Profile (PVLP-SLP) is certified for
use as a horizontal termination cap only on fireplaces
manufactured by Hearth & Home Technologies with IPI (in-
termittent pilot ignition) gas controls. Fireplaces equipped
with millivolt type gas controls CANNOT use this product.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hearth & Home PVLP-SLP
Summary of Contents for Hearth & Home PVLP-SLP
- Page 1 A. Components and Service Parts List ....2 B. Installation of PVLP-SLP ......3 ply with local, regional, state and national codes and regulations.
-
Page 2: A. Components And Service Parts List
NOTE: Wire Harness connecting PVI to appliance sold separately. NOTE: Wire Harness connecting PVLP-SLP to appliance sold separately. The length of wire harness needed varies by installation. For all appliances equipped with IntelliFire™ or IntelliFire™ Plus ignition, other than the PRIMO, PV-IPI-CK con- The length of wire harness needed varies by installation. -
Page 3: B. Installation Of Pvlp-Slp
CAUTION! Failure to install, operate, and maintain the power venting system in accordance with manufacturer's instructions will result in conditions which may produce bodily injury and/or property damage. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 4: A. Installation Of Vent Pipe
• Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated. Figure 2.1 Silicone Sealant Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 5 B. Vent/Pipe Regulations (continued) WARNING! Risk of Fire! • A minimum length run of initial vent pipe is required between the appliance and the inlet of the PVLP-SLP on some appliance models. • Some models require DVP Series pipe for the initial minimum vent section directly off the appliance.
- Page 6 APPLIANCE NOTICE: If a a pipe configuration includes a vertical component that goes downward, a vertical component going back upward is not allowed. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 7 See Chart in Section 2.C: "Venting Length - Model Categories and PVLP-SLP with certain appliance mod- Length Requirements by Termination Type." els. See Table 2.1. Figure 2.2 Horizontal PVLP Orientation Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 8 See Chart in Section 2.C: "Venting Length - Model Categories and PVLP-SLP with certain appliance mod- Length Requirements by Termination Type." els. See Table 2.1. Figure 2.3 Horizontal PVLP Orientation Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
-
Page 9: Requirements By Termination Type
Total Venting Length (Feet) Includes both horizontal and vertical section of pipe # of Elbows These configurations are not allowed. Table 2.3 Allowable Vent Runs - Horizontal Termination Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 10: A. Framing And Clearances
2. Cut a 10 inch high by 13 inch wide opening into the exterior of the structure. Stay inside of the newly installed framing as shown in Figure 3.2. 10 IN. Figure 3.2 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 11: Clearance To Combustibles
Figure 3.4 will need to be constructed. 1-1/2 in. [38mm] 1 in. [25mm] 20-3/4 in. [527mm] 2 in. [51mm] 12 in. [305mm] Figure 3.4 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 12: B. Installing Vent Cap
• Cap contains silicone sealant which could affect adherence of paint. Please advise local painter of silicone content. Figure 3.8 Figure 3.5 Figure 3.9 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 13 8. To open the baffle, turn the adjustment bolt counter clockwise. See Figure 3.15. Figure 3.13 Figure 3.10 Figure 3.14 Figure 3.11 Figure 3.15 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 14 Remove the four screws that attach the front cover, then remove the cover. See Figure 3.17. Figure 3.16 Figure 3.17 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 15 PVLP-BEK around the entire metal flange, as (SECURE FIRST) shown in Figure 3.23 with the dotted line. Figure 3.20 PLVP-BEK Attached to Wall Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 16 Silicone (with a minimum of 300° F continuous exposure rating) should also be applied where PVLP- Figure 3.25 SLP and PVLP-BEK meet, as shown in Figure 3.22. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
-
Page 17: Controls
6V DC (AA X 4) THERMOSTAT WIRE ASSEMBLY / WALL SWITCH WIRE STEP 6 Figure 4.1 IntelliFire Plus™ (Black) IPI Module Wiring as Shipped from Factory Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 18 VALVE TRANSFORMER 3 VAC STEP 2 STEP 6 REMOTE JUMPER WIRE PLUG-IN Figure 4.2. IntelliFire™ (Green) IPI Module Wiring as Shipped from Factory Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 19 STEP 7 8K1-PVI WIRE HARNESS VALVE STEP 6 BROWN ACCESSORY CABLE GROUND Figure 4.3 PVLP Wiring for IntelliFire™ Plus RC100, RC200, RC300 Controls Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 20 STEP 5 8K1-PVI WIRE HARNESS STEP 6 ORANGE BROWN VALVE (PILOT) ACCESSORY CABLE GREEN GROUND (MAIN) Figure 4.4 PVLP Wiring for Intellifire™ IPI Module Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 21 TO PVI CONTROL BLOWER GREEN NOTE: Use threaded nut to secure accessory cable to power vent. BLACK WHITE Figure 4.5 Internal PVI Wiring Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
-
Page 22: Ift) Controls
- DO NOT connect PVI-WH connector to IFT- ACM. - Disconnect 6V power to lock-out appliance. Failure to follow instructions could result in a fire or explosion. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 23 STEP 4 (OPTIONAL) 6V DC SPLITTER BATTERY PACK STEP 2 APPLIANCE ON/OFF CONTROL STEP 3 Figure 4.6. IFT-RC400 Wiring Diagram without Power Vent Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 24 WARNING! Risk of Shock! DO NOT touch male pins. Leave rubber cap on all ports unless port is being con- nected to a load. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
- Page 25 15. Restore Power to the control module. 13. Plug (3) connector plug on accessory cable into Pow- er Vent port on IFT-ACM. See Figure 4.10. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
-
Page 26: Control Module (Ift-Ecm)
Successful pairing will be indicated by a double beep from the IFT-ECM. 3. If the pairing is unsuccessful, repeat steps 1 & 2. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 27: A. Installation Inspection
The Power Vent will continue to run for 20 min. WARNING! After installation of Power Vent components, the RC400 and IFT-ECM MUST BE Re-Paired for safe operation. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 28: D. Maintenance
7. Remove the two screws holding the pressure switch bracket to the exhaust housing. See Figure 5.8. 8. Remove the pressure switch. See Figure 5.9. Figure 5.4 Figure 5.5 Figure 5.1 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 29 Figure 5.6 Figure 5.7 Figure 5.8 Figure 5.9 Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
-
Page 30: F. Pvlp-Slp Troubleshooting
This will block a portion of the strong draft. Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... -
Page 31: G. Ift-Controls And Pvi-Slp Power Vent Troubleshooting
For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com. Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044 www.hearthnhome.com Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17... - Page 32 Refer to the manual from the Majestic Power Vent kit PFLDV None for instructions on wiring the PVLP-SLP to Majestic STLDV None Fireplaces VCFDV None VHLDV None VWDV 24" 12" WDVST 12" Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. L • 08/10/17...
Need help?
Do you have a question about the PVLP-SLP and is the answer not in the manual?
Questions and answers