• Manual or DMX-controlled: 6 different channel modes (8bit & 16bit dimming) for maximum flexibility. • Can be used 1 channel DMX mode, with CCT-preset of your choice. • Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (Briteq ®...
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit. Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy. BRITEQ 2/13 BT-THEATRE 400TW ®...
Page 5
PC! Instead, this USB-connector makes it very easy to add wireless DMX to the ® unit! Just add the (optional) WTR-DMX DONGLE from BRITEQ and you will get wireless DMX! Moreover, you will be able to connect other DMX-controlled equipment to the DMX-...
• Use ▲/▼ buttons to select the desired DMX512 address. The last occupied DMX-address is also shown: makes it easier to set the address of the next unit in the chain. • Once the correct address shows on the display, press the ENTER button to confirm. BRITEQ 4/13 BT-THEATRE 400TW ®...
Page 7
Last JOB hours xxxx Hrs LED Temp. xxx °C / F INFORMATION ERROR info xxxxxxxx Model Name BT-THEATRE 400TW Firmware V. V x.xx RDM UID 0x21220044xxxx FIXTURE Set – Used to configure different parameters if the projector. NO DMX Mode Used to set how the projector reacts when the DMX-signal disappears.
Page 8
• 20’000 Hz: highest possible PWM frequency, • Once the desired value shows on the display, press the ENTER button to confirm. Remark: The default value (1’200 Hz) gives excellent dimming performance with very low dimmer noises. BRITEQ 6/13 BT-THEATRE 400TW ®...
Page 9
• Use ▲/▼ buttons to select one of these options: • Celcius: LED-temperature is shown in degrees Celcius °C. • Fahrenheit: LED-temperature is shown in degrees Fahrenheit F. • Press the ENTER button to confirm. BRITEQ 7/13 BT-THEATRE 400TW ®...
Page 10
• Press the ▲/▼ buttons until the desired function is showing on the display. • Press the ENTER button: • No errors: display shows NONE • Errors to report: the error will be shown on the display so you can take action. BRITEQ 8/13 BT-THEATRE 400TW ®...
• Press the ENTER button: the display shows the firmware version. Note: The firmware of this unit can be upgraded using our special “Firmware Updater 2” (separately available from Briteq). More information about this can be found in the user manual of the firmware updater or our website: https://briteq-lighting.com/firmware-updater-2 RDM UID Shows the unique RDM identification code of the projector.
Page 12
• The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique device ID. • The DMX-controller asks each RDM device for some basic data so it knows which devices are connected. The projector will respond: • Device name: BT-THEATRE 400TW • Manufacturer: ® Briteq • Category: LED Dimmer •...
Page 13
Remark 1: 1CH and 2CH modes have no FOCUS channel: FOCUS is adjusted in the setup menu. Remark 2: in the function channel you can choose "DIM behavior = DIMMER SPEED". The dimmer speed value is set using the setup menu. BRITEQ 11/13 BT-THEATRE 400TW ®...
Page 15
ENGLISH OPERATION MANUAL V1.1 Photometric data Lux charts The information might be modified without prior notice You can download the latest version of this user manual on our website: www.briteq-lighting.com BRITEQ 13/13 BT-THEATRE 400TW ®...
Need help?
Do you have a question about the BT-THEATRE 400TW and is the answer not in the manual?
Questions and answers