Advertisement
SET UP
Note: Please remove the protective film on the
control panel display for better usage.
Remove the plastic bag around the filter before
using the product.
Always keep unit OFF when changing the filters.
1
Open the main body of the unit
Open the product by pressing the release buttons
on the sides of the unit, then lift up the top part of
the main body. (ref. page 5, picture 1).
2
Take out the filter and remove the filter bag
Carefully remove the plastic bag around the filter
and discard appropriately.
3
Install the filter
Carefully insert the filter back into the product
(either end of the filter works). Make sure that the
filter is placed in the center of the cavity.
4
Put back the top part of the main body
Put back the top part of the main body to close
the product till it is securely in place. The mark
"FRONT" should be facing the front side of the
product.
OPERATION
Caution: After filter is installed correctly, please
ensure product is placed on a leveled surface
before proceeding further. Ensure there is
enough free space over and around the product.
5
Connect the power plug.
6
Power on
Press the ON/OFF button
purifier, the unit will run in default setting (SMART
mode) when using the product the first time.
Next time you start the unit it will resume the last
settings you had before turning OFF the product.
NOTE: When turning ON the air purifier, it will take
about 10 seconds for the sensors to calibrate and
analyze the air quality. During this time, the air
quality indicator will pulsate slowly in white.
7
Mode selection
Press the MODE button
between the two modes: SMART and MANUAL
SMART: In the SMART mode the unit will utilize
the sensor data as input to decide on the
appropriate fan speed, depending on the air
quality in the room. The fan speed can not be
adjusted by the user under this mode. Please see
the AIR QUALITY INDICATOR section for more
details.
www.electrolux.com
to turn ON the air
once to toggle
SMART QUIET: In the SMART QUIET mode the unit
will run as quiet (control panel indicators dimmed
& lower fan speed) as possible to allow for sleep.
MANUAL: In the MANUAL mode the unit will
utilize the sensor data as input only to show the
air quality level via the air quality indicator but
will not self-adjust the fan speed. This mode
is best utilized for a quick burst of cleaning,
especially when the user anticipates an increase in
particulate matter in the room due to household
chores (e.g. vacuuming).
8
Air speed control
While in MANUAL mode, Press the FAN button to
adjust the fan speed, the fan speed indicator will
show the fan speed.
The unit has 3 levels fan speed.
NOTE: The unit will ramp up OR down to chosen
speed setting gradually.
FEATURE ICONS AND INDICATORS
9
ALERT
The alert icon
will light up to alert you of a
possible electrical or electronic error with your
unit. Please refer to the App for details on the
error type, component details and any mitigating
actions. More details can also be found in the
ERRORS & TROUBLESHOOTING section below.
10
FILTER CHANGE and RESET
FILTER CHANGE: The filter in the unit cannot be
washed, they can only be replaced. The filter
change icon
will light up to remind you to
change your filter. Always ensure the plastic
protective bag is removed before its use in the
unit.
FILTER RESET: After the used filter is replaced, long
press the MODE button
filter change indicator will reset.
11
WIFI
The unit is equipped with a WiFi module, which
enables remote control and access to many more
features including time-based tracking of your
indoor air quality data. When the unit is connected
to the home WiFi, this icon
icon is blinking, it indicates a temporary loss of
WiFi connectivity – please refer to the Electrolux
App for more details.
Long press the ON/OFF button
to activate or deactivate wireless network.
NOTE: Download our Electrolux App and follow
the step-step onboarding instructions to bring
the air purifier online.
for 3 seconds and
will light up. If the
for 5 seconds
7
Advertisement
