Working Advice; Repair Service; Disposal And Recycling - stayer SCP 125 DIAMANT Original Instruction Manual

again.
Note: For bevel cuts, the cutting depth is smaller than the
setting indicated on the cutting-depth scale 26.
Cutting Marks
45 0
The 0° cutting mark 9 indicates the position of the saw
blade for right-angled cuts. The 45° cutting mark 8
indicates the position of the saw blade for 45° cuts.
For precise cuts, position the circular saw against the
workpiece as shown in the figure. It is best to carry out a
trial cut.
Laser guide
The laser guide is turned on by pressing button 23 and will
remain on until pressed again.
- Mark the cut line on the work piece.
- Adjust the depth and / or bevel angles of the cut as
necessary.
- Turn on the laser guide by pressing the on / off button 23
and align the cutting line on the workpiece.
- When the blade reaches its maximum speed (approx. 2
seconds), make the cut.
- At the end of the cut, turn off the laser guide, pressing
again 23.
Starting Operation
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and
keep it pressed.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.

Working Advice

Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting
direction.
Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade.
Therefore, use only sharp saw blades that are suited for
the material to be worked.
- Before any work on the machine itself, disconnect
the battery.
Sawing Wood
The correct selection of the saw blade depends on the
type and quality of the wood and whether lengthway or
crossway cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide
The parallel guide 10 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 7 and slide the scale of the parallel
guide 10 through the guide in the base plate 12. Adjust the
45 0
ENGLISH
22
desired cutting width as the scale setting at the respective
cutting mark 9 or 8; see Section "Cutting Marks". Tighten
wing bolt 7 again.
Sawing with Auxiliary Guide
For sawing large workpieces or straight edges, a board or
strip can be clamped to the workpiece as an auxiliary
guide; the base plate of the circular saw can be guided
alongside the auxiliary guide.

Repair service

Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
Transport
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements. When being transported by third parties
(e.g.: air transport or forwarding agency), special
requirements on packaging and labelling must be
observed. For preparation of the item being shipped,
consulting an expert for hazardous material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations.

Disposal and recycling

The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/
UE for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Battery packs/batteries:
Li-Ion:
Please observe the instructions in
section "Transport". Do not dispose of
battery packs/batteries into household
waste, fire or water. Battery packs/
batteries should be collected, recycled
or disposed of in an environmental-
friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be
recycled according the guideline 2006/66/CE.
Subject to change wlthout notlce.
22