Product Description And Specifications; Technical Data - stayer SCP 125 DIAMANT Original Instruction Manual

- Do not use high speed steel (HSS) saw blades.
Such saw blades can easily break.
- Do not saw ferrous metals. Red hot chips can ignite
the dust extraction.
- When working with the machine, always hold it
firmly with both hands and provide for a secure
stance. The power tool is guided more secure with
both hands.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Batteries use and care
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction,
until the tool can be inserted. Insert the tool. Firmly
tighten the collar of the keyless chuck 2 by hand in
rotation direction . This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.
ENGLISH
20

Product Description and Specifications

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
Intended Use
The machine is intended for lengthways and crossways
cutting of wood with straight cutting lines as well as mitre
cuts while resting firmly on the workpiece. With suitable
saw blades, thin-walled non-ferrous metals, e. g., profiles,
can also be sawed.
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com
Product Features
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 On/Off switch.
2 Lock-off button for On/Off switch.
3 Auxiliary handle (insulated gripping surface).
4 Spindle lock button.
5 Scale for mitre angle.
6 Wing bolt for bevel-angle preselection.
7 Wing bolt for parallel guide.
8 Cutting mark, 45°.
9 Cutting mark, 0°.
10 Parallel guide.
11 Retracting blade guard.
12 Base plate.
13 Lever for retracting blade guard.
14 Chip ejector.
15 Blade guard.
16 Handle (insulated gripping surface).
17 Key.
18 Clamping bolt with washer.
19 Clamping flange.
20 Saw blade*.
21 Mounting flange.
22 Saw spindle.
23 Laser guide on / off switch.
24 Laser guide exit hole.
25 Lever for preselection of cutting depth.
26 Cutting depth scale.
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of acces-
sories can be found in our accessories program.

Technical data

= Voltage
= Battery power
= Load speed.
= Disc dimension.
Ø
= Cutting capacity 90º
= Cutting capacity 45º
= Weight.
20