Sunnydaze Decor FWD-426 Manual

Mediterranean inspired tiered outdoor water fountain

Advertisement

MEDITERRANEAN INSPIRED
TIERED OUTDOOR WATER FOUNTAIN
Read assembly instructions carefully and follow the care instructions. Save this document for future reference.
Assemble components on a soft, clean surface to avoid scratching or damaging the finish.

HELPFUL HINTS

When first plugged in, there may be air in the pump. It may take several minutes for trapped air to escape, allowing water to flow.
Additional water may need to be added after the pump begins to circulate water through the fountain.
FD50093
Purchase Date:
/
/
Order/Customer Reference Number:
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
customerservice@sunnydazedecor.com, or via our contact us page at
FWD-426
No.
Parts
A
Fountain Topper
B
Middle Tier
C
Column
D
Large Tier
E
Pedestal
F
Electric Submersible Pump
G
Rubber Cap
H
Pump Access Cover
I
String Rocks

ASSEMBLY

1. Align Large Tier (D) with the notches in Pedestal (E), twist the large
tier clockwise to lock in place.
2. Place the electric submersible pump in the bottom of the large tier,
next to the built-in tube. Run Pump (F) power cord through the tube,
then out through the groove under the pedestal.
3. Ensure the pump sits flat in the bottom tier. Affix Rubber Cap (G)
over the tube and pump power cord.
4. Place Column (C) on Large Tier (D) and twist the column clockwise
to lock in place.
5. Place Middle Tier (B) on Column (C) and twist the middle tier
clockwise to lock in place.
6. Run the built-in water tube from Fountain Topper (A) through the
fountain, gently placing the topper on the middle tier.
7. Firmly connect the water tube to the pump and install the pump
access cover.
8. Fill all tiers with enough water to keep the pump fully submerged
during operation, approximately 5.5 gallons.
9. Plug the power cord into a properly grounded GFCI outlet.
11/2021
https://tiny.cc/SunnydazeWarranty
https://tiny.cc/SunnydazeContact
Qty.
1
Inspect packaging to ensure all
1
parts are accounted for before
disposing of packing materials.
1
1
The water tube is built into
NOTE:
1
the fountain topper. Take care when
1
handling the water tube; detaching
1
the water tube from the fountain will
1
damage the fountain and void the
1
product warranty.
SET
Page 1 / 2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FWD-426 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sunnydaze Decor FWD-426

  • Page 1 Order/Customer Reference Number: Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with the date of purchase as well as photos of the merchandise defect, must be provided.
  • Page 2 STRING ROCKS (optional) String rocks can be used to reduce splashing and/or fountain noise. To reduce splashing, moisten the string and place the rock in each notch of the tier, allowing the string to reach down towards the tier below. Note, this will also help provide some minor wind resistance. The string rock system will reduce the sound the water makes, but it will increase the runtime by reducing the amount of water splashing outside of the fountain.

Table of Contents