Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HIKOKI C 3606DB
Summary of Contents for HIKOKI C 3606DB
- Page 1 C 3606DB Handling instructions...
- Page 5 45° 0° High mode Medium mode Silent mode Medium High...
- Page 7 45° 30° 15° 0°...
-
Page 10: General Power Tool Safety Warnings
c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi... - Page 11 h) Keep handles and grasping surfaces dry, clean c) Adjust the cutting depth to the thickness of the and free from oil and grease. workpiece. Slippery handles and grasping surfaces do not Less than a full tooth of the blade teeth should be visible allow for safe handling and control of the tool in below the workpiece.
-
Page 12: Additional Safety Warnings
e) Do not use dull or damaged blades. 17. Ensure that the switch is in the OFF position. If the battery Unsharpened or improperly set blades produce narrow installed to power tool while the switch is in the ON kerf causing excessive friction, blade binding and position, the power tool will start operating immediately, kickback. -
Page 13: Caution On Lithium-Ion Battery
30. Use a saw blade with a displayed speed that is equal to CAUTION ON LITHIUM-ION BATTERY or higher than the rotation speed displayed on the tool. 31. Use a saw blade that complies with EN847-1. To extend the lifetime, the lithium-ion battery equips with the 32. -
Page 14: Regarding Lithium-Ion Battery Transportation
WARNING NAMES OF PARTS (Fig. 1–Fig. 34) If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing fi re. When storing the lithium ion battery, obey surely the rules of Switch following contents. -
Page 15: Standard Accessories
Mode selector switch etc.) cannot be used with this tool. NOTE Lighting mode switch Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to Always ON (turns off after 60 seconds) change without prior notice. - Page 16 ○ Do not block the air vent. Otherwise the interior will CHARGING overheat, reducing the charger’s performance. ○ If the cooling fan is not operating, contact a HiKOKI Before using the power tool, charge the battery as follows. Authorized Service Center for repairs.
-
Page 17: Mounting And Operation
Cutting at right angles Regarding electric discharge in case of new batteries, etc. Inclined cutting (+45° direction) Inclined cutting (–5° direction) As the internal chemical substance of new batteries and batteries that have not been used for an extended period Dismounting the saw blade is not activated, the electric discharge might be low when Mounting the saw blade... - Page 18 In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. Important notice on the batteries for the HiKOKI cordless power tools Please always use one of our designated genuine Space between Air gun batteries.
-
Page 19: Troubleshooting
TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. Symptom Possible cause Remedy Tool doesn’t run No remaining battery power Charge the battery. - Page 20 5 mm C3606DB (NN)
- Page 21 Multi Volt (Li-ion) UC18YSL3 (14.4 V–18 V) 329897 338915 338916 338917 944459 990666 302756 316161 379511 379784 337528 379560...
- Page 24 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99747511 G Printed in China...
Need help?
Do you have a question about the C 3606DB and is the answer not in the manual?
Questions and answers