Kitchen Exhaust Fan GLEB Installation and Maintenance ImporTaNT INFormaTIoN, saFETy NoTEs, TECHNICaL DEsCrIpTIoN 1. ImporTaNT INFormaTIoN Fläkt Woods does not accept responsibility for any damage that Fläkt Woods GLEB kitchen exhaust fan HT-versions comply with the requirements for EN 12101-3 standard and health and safety can be attributed to non-observance of these instructions.
Hz induction motor 3.3 FaN aND moTor raNGE max speed motor power Current Voltage max. frequency Fan code motor code motor IEC r/min 1,68 / 0,97 GLEB-1-025-3-037-0 APAL-2-00037-1-2-6 2900 0.37 51.8 2,74 / 1,58 GLEB-1-031-3-055-0 APAL-4-00055-1-2-6 2200 0.55 78.6 GLEB-1-040-3-110-0...
Kitchen Exhaust Fan GLEB Installation and Maintenance TECHNICaL DEsCrIpTIoN, TraNsporT 3.5 DImENsIoNs Ø OUTLET Fan size Ø Inlet Ø outlet Weight [kg] 4. TraNsporT 4.1 TraNsporT INspECTIoN 4.3 INTErmEDIaTE sToraGE Check the fan immediately after you receive it and make sure that If the fan is to be stored before use or in between uses, the it has not been damaged during transport.
Installation and Maintenance Kitchen Exhaust Fan GLEB mouNTING INsTruCTIoNs 5. mouNTING INsTruCTIoNs 5.6 ELECTrICaL CoNNECTIoNs All electrical connections must be wired by authorised person- 5.1 INsTaLLaTIoN oF THE FaN nel only. The necessary electrical and safety precautions must be The fan is secured to a base by M8 pin bolts and nuts (4 pcs) in taken into account.
Kitchen Exhaust Fan GLEB Installation and Maintenance CommIssIoNING, maINTENaNCE 6. CommIssIoNING 7.2.2 Inspection intervals Inspection intervals can be defined by local authorities. 6.1 saFETy CHECKING If nothing else is mentioned, the fan shall be tested according to Open the cleaning hatch (see 3.1 Design, part 9) and rotate the the intervals in table, but at least once a year.
Installation and Maintenance Kitchen Exhaust Fan GLEB maINTENaNCE 7.2.3 Checking the motor bearings 7.3 rEpLaCING THE moTor If the standard fan is used also in the normal ventilation, after The fan has to be disconnected from the duct system and mains 40000 hours of operation the fan is to be checked twice a year before the motor can be replaced.
Kitchen Exhaust Fan GLEB Installation and Maintenance maINTENaNCE 7.4 rEpLaCING THE ImpELLEr 7.5 FINaL INspECTIoN Check that: The fan has to be disconnected from the duct system before the impeller can be replaced. – The overlap between the impeller and the inlet cone equals with the one measured before the maintenance.
Page 9
Installation and Maintenance Kitchen Exhaust Fan GLEB Scrapping, Spare partS, prOduct cOdeS 8. Scrapping 11. prOduct cOdeS Kitchen exhaust fan gleB-a-bbb-c-ddd-e The materials used in the fan are listed below. Disposing of those materials should be carried out according to valid instructions. Environment (a) component Material...
Kitchen Exhaust Fan GLEB Installation and Maintenance 12. DECLaraTIoN oF CoNFormITy maNuFaCTurEr’s DECLaraTIoN As defined by the EC Council Directive on machinery 98/37/EEC concerning the machinery, which is intendent to be assembled with other machinery/machinery components to constitute machinery. manufacturer: Fläkt Woods Oy address: Kalevantie 39...
Installation and Maintenance Kitchen Exhaust Fan GLEB 13. DECLaraTIoN oF pErFormaNCE Fläkt Woods 9987GB 2016.02.03 Specifications are subject to alteration without notice...
Page 12
Manufacturer: Fläkt Woods oy Kalevantie 39, FI-20520 Turku, Finland Tel. +358 20 4423000 email info@flaktwoods.com www.flaktwoods.com » To learn more about our offering and get in contact with your near- est sales representative please visit www.flaktwoods.com...