Harrod RUG-052 Manual

Harrod RUG-052 Manual

Aluminium rugby posts

Advertisement

Quick Links

Code:
RUG-052/199/200/201/210/211/212
Product:
Aluminium Rugby Posts
Aluminium Rugby Posts
1. 4 x FEP273
Hinge Assembly
2. 4 x FEQ731
Bottom Upright
2. 4 x FEQ741
Bottom Upright
3. 1 x FEQ730
Pair of Crossbars
4. 4 x WEQ735 Ground Socket
5. 4 x FEQ099
Top Upright
5. 4 x FEQ733
Top Upright
6. 4 x FPK741
Rugby Fittings

Tools Required

1 x 22mm Spanners
2 x 19mm Spanners
2 x 17mm Spanners
1 x Spirit Level
1 x Tape Measure
2 x Step Ladders

Pack Contents:

(RUG-210/211/212)
(RUG-199/200/201)
(RUG-210/211/212)
(RUG-201/210)
(RUG-200/211)
(RUG-199/212)
View of Product
5
Not RUG-199/212
6
Only RUG-199/212
2
3
1
Only RUG-210/211/212
4
Fig 1
RUG-052 Hinge Assembly only
1. 4 x FEP273
FPK741 Rugby Fittings Pack
7. 4 x CAP310
FPK741 fittings pack only supplied
with RUG-199 & RUG-212
Fittings
IMPORTANT PLEASE READ THE ASSEMBLY
I N S T R U C T I O N S C A R E F U L LY B E F O R E
STARTING TOASSEMBLE YOUR POSTS.
IMPORTANT Assembly of these posts should not take
place in windy conditions.
For safety reasons; Post Protectors must be used with all
Hinged Rugby Posts to cover the hinge arrangement.

Important Note for RUG-052

If RUG-052 has been purchased for adapting an
existing set of rugby posts, you will need to cut down
your existing uprights as follows:
For sockets installed 25mm below ground level the
distance from the underside of the channel to the
bottom of the upright needs to be 2934mm. For
sockets flush with ground level this needs to be
2909mm.

Safety Notes

1
A risk assessment must be carried out on the
erection of Hinged Rugby and RugbyAdaptors.
2
Hinged posts covered by this instruction may be
"walked-up" by 2 suitably trained people wearing
appropriate PPE unless the Risk Assessment
highlights the requirement for
3
Always check fasteners before use and tighten
where necessary.
4
Periodically apply grease to hinge fixing bolts to
pre-long the life of posts.
5
Posts should always be taken down if strong
winds are forecast.
INS619
26/09/2018
Revision 10
©
Harrod UK Limited
Hinge Assembly
(contains)
Ø80mm Plastic Caps
7
mechanical assistance
.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RUG-052 and is the answer not in the manual?

Questions and answers

Summary of Contents for Harrod RUG-052

  • Page 1 For safety reasons; Post Protectors must be used with all Hinged Rugby Posts to cover the hinge arrangement. Important Note for RUG-052 If RUG-052 has been purchased for adapting an existing set of rugby posts, you will need to cut down your existing uprights as follows:...
  • Page 2 Code: RUG-052/199/200/201/210/211/212 Product: Aluminium Rugby Posts Assembly Instructions Dig holes 1100x1100x1000 deep at centres of Install Sockets 5676mm mm as shown in Fig 2. Concrete the sockets in 25mm below ground level and leav approx 0mm from top of concrete to ground level (to replace turf .

This manual is also suitable for:

Rug-199Rug-200Rug-201Rug-210Rug-211Rug-212

Table of Contents