Breakdown Of Parts - Wayne-Dalton 44 Double Flush Manual

NOTE: The illustrations shown on this page are general
representations of the door parts. Each specific door
models may have unique variations.
H4.
C1.
A1.
F1.
I10.
D1. D2.
C2.
C1.
H3.
B1.
H2.
A. FLAG ANGLES (AS REQUIRED):
A1. Fully Adjustable (F.A.) Flag Angles
B. JAMB BRACKETS (AS REQUIRED):
B1. Fully Adjustable (F.A.) Jamb Brackets
C. TRACK ROLLERS (AS REQUIRED):
C1. Short Stem Track Rollers
C2. Long Stem Track Rollers
C3. Short Stem Tandem Track Rollers
C4. Long Stem Tandem Track Rollers
D. GRADUATED END HINGES:
D1. Single Graduated End Hinges (S.E.H.), Industry Standard
D2. Double Graduated End Hinges (D.E.H.), Industry Standard
D3. Half Center Hinges (As required)
E. STACKED SECTIONS:
E1. Top Section
E2. Intermediate(s) Section / E3. Bottom Section
F. TOP FIXTURES (AS REQUIRED):
F1. Top Fixtures
G. STRUT(S) (AS REQUIRED):
G1. Strut (2" U-shaped) / G2. Strut (3" U-shaped)
H. TRACKS (AS REQUIRED):
H1. Left Hand and Right Hand Horizontal Track Assemblies
H2. Left Hand and Right Hand Vertical Tracks
H3. Left Hand and Right Hand Riveted Vertical Track Assemblies

BREAKDOWN OF PARTS

E1.
D3.
I12.
E2.
J2.
I1.
E3.
I2.
C4.
J1.
E4.
C3.
M1.
L1.
M1.
K1.
I2.
I12.
H4.
C1.
F1.
G1.
A1.
G2.
B1.
I4.
H2.
K1.
H3.
I1.
I7.
NOTE: For Item (J2), The Rear Center Back Hang Assemblies are to used for
I3.
I8.
all doors over 11'0" door height and over 14'0" door width. One Rear Center
Back Hang Assembly, per side.
NOTE: For Item (J3), The Rear Center Back Hang Assemblies are to used for
all doors over 16'0" door height. Two Rear Center Back Hang Assemblies,
per side.
H4. Left Hand and Right Hand Angle Mount Vertical Track Assemblies
I. TORSION SPRING ASSEMBLY (AS REQUIRED):
I1. Left Hand and Right Hand Torsion Springs (As Required)
I2. Counterbalance Lift Cables
I3. Left Hand and Right Hand Cable Drum
I4. Center Bracket (As Required)
I5. Center Bracket Bearing (As Required)
I6. Torsion Shaft / Torsion Keyed Shaft (As Required)
I7. Torsion Keyed Shafts (As Required)
I8. Keys (As Required)
I9. Center Coupler Assembly (As Required)
I10. Cable Sheaves
I11. Oval bearings (As Required)
I12. Cable sheave saddles
J. REAR BACK HANGS:
J1. Left Hand And Right Hand Rear Back Hang Assemblies
J2. Left and Right Hand Rear Center Back Hang Assemblies (As Required)
J3. Left and Right Hand Rear Center Back Hang Assemblies (As Required)
K. BOTTOM CORNER BRACKETS (AS REQUIRED):
K1. Left Hand and Right Hand Bottom Corner Brackets
L. BOTTOM WEATHER SEAL (AS REQUIRED):
L1. Bottom Weather Seal (Door Width), (Nails Not Supplied)
M. TRACK ROLLER CARRIERS (AS REQUIRED):
M1. Track Roller Carriers
3
J3.
I10.
H1.
K1.
I6.
I1.
I8.
I5.
I11.
I9.
I8.
I5.
I5.
I4.
I11.
I4.
J2.
J1.
I3.
I8.
I7.