Table of Contents
Advertisement
Quick Links
Aluminum Full View
Models 464, 451,
452
T
o r s i o n
c
oMMercial
s
l
Tandard
ifT
i
i
nsTallaTion
nsTrucTions
M
anual
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2020
Wayne Dalton, a division of Overhead Door Corporation
T a b l e O f C o n t e n t s
a
o
'
nd
wner
s
IMPORTANT NOTICES!
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box
67, Mt. Hope, OH., 44660
Part Number
352194
2
2
2
4
5
6
7
8
13
22
22
22
22
22
22
23
24
24
24
25
REV9_01/24/2020
Advertisement
Table of Contents
Related Manuals for Wayne-Dalton 464
Summary of Contents for Wayne-Dalton 464
-
Page 1: Table Of Contents
This Installation document is available at no charge from: - Your local Wayne Dalton Sales Center, or - Online at www.Wayne-Dalton.com, or - By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660... -
Page 2: Pre-Installation
Existing Door & Prepar- ensure door operates freely. ing the Opening. These are available for download at www.Wayne-Dalton.com or at your 15. Test electric opener’s safety features monthly, following opener manufacturer’s instruc- local Wayne Dalton Sales Center. - Page 3 FOUND NOT TO BE SOUND, MUST BE REPLACED. Extend Jambs To Opening Height Plus Dim. “Y” Plus 1-1/2” (Minimum Length) Minimum For Torsion counterbalance systems, a suitable mounting surface (2” x 6”) must be firmly Headroom attached to the wall, above the header at the center of the opening. For Wall Angles Cut 3”...
-
Page 4: Package Contents
2” Track At The Floor: 5-1/2” 3” Track At The Floor: 4-3/4” 4” Min. 3-1/2” Min. Pre-cast Wall With Corner Angle Pre-cast Wall With Corner Sideroom Sideroom Angle 5/16” x 1” Self 5/16” x 1” Self drilling screw drilling screw 1”... -
Page 5: Door Section Identification
Top fixture slides Top fixture bases “L” Reinforcing brackets (as required) (as required) (as required) Strut (if included) Door sections (as required) Torsion shaft / Torsion keyed shafts (as required) F.A. Center coupler Torsion keyed shafts (as required) Jamb brackets Keys assembly Torsion springs... -
Page 6: Tools Required
21” / 19-1/2” sections height stacked to the top. Unless your door is three sections height, you will not receive an Intermediate I section. NOTE: If you have Model 464, the door height only goes up to or equal to 14’0”, 7 sections high. -
Page 7: Breakdown Of Parts
BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations. NOTE: For Item (K2), The Rear Center Back Hang Assemblies are to used for all doors over 11’0” door height and over 14’0”... -
Page 8: Door Installation Instructions
IF YOU DID NOT RECEIVE AN ANTI-SAG BRACE: Next, align the bottom corner bracket DOOR INSTALLATION horizontally with the bottom edge of the bottom section and also align the bottom corner bracket vertically with the left bottom edge of the bottom section. Attach each bottom corner INSTRUCTIONS brackets to the bottom section using the appropriate 1/4”... - Page 9 TRACK APPLICATIONS; THE OUTER HOLES ARE USED ON DOORS WITH 3” TRACK APPLICA- TIONS. Attaching Hinges Left hand bottom corner bracket NOTE: Refer to door section identification, located in the pre-installation section of this manual. NOTE: The graduated hinges can be identified by the number stamped onto their lower hinge leaf.
- Page 10 (1) 5/16”-18 x 3/4” Top section Carriage bolt Long stem #1Center hinge(s) track roller Top fixture slide (8) 1/4”-20 x 7/8” Self drilling screws #1 / #3 Graduated Top fixture end hinges base Lower Top fixture leafs slides #2 Graduated end hinges or higher (4) 1/4”-20 x 7/8”...
- Page 11 NOTE: If you don’t have wall angle seals, then skip this step. Refer to Package Contents and or illustrations below, to determine which wall angle seals you have received. Wallangle Starting with the left hand wall angle, align the profile of the wall angle seal with the inside Riveted track track flag angle...
- Page 12 HANDLE(S) MUST BE 20” MINIMUM TO 30” MAXIMUM. IF NECESSARY, REPOSITION THE UPPER LIFT HANDLE(S) TO STAY WITHIN THE REQUIRED DIMENSION. Wall Angle Using the holes in the lift handle as a template, mark the hole locations onto the section sur- face.
-
Page 13: Counterbalance Installation Instructions
Horizontal track angle Attaching Horizontal Tracks Level Horizontal track NOTE: Depending on your door, you may have Fully Adjustable Flag Angles, Riveted Vertical Track Assemblies or you may have Angle Mount Vertical Track Assemblies. Refer to Package Contents / Breakdown of Parts, to determine which Flag Angles / Vertical Track Assemblies Horizontal Level track angle... - Page 14 NOTE: Drill 3/16” pilot holes into header for the lag screws. bracket as a drill template and drill a 3/8” hole (3-1/2” deep) and secure to anchor. FOR STEEL CONSTRUCTION: Secure each center bracket using (4) 5/16” x 1” self-drilling WARNING and tapping screws, as shown.
- Page 15 Space center brackets 12” apart WARNING on applications requiring center coupler assembly THESE SPRING MOUNTING TECHNIQUES ARE NOT SUPPORTED FOR 800- NOTE: Actual Girt center brackets 32 CABLE DRUMS. THESE INSTRUCTIONS ARE ALSO NOT APPLICABLE may vary, see FOR 5750-120 CABLE DRUMS WITH 72” OR MORE HIGH-LIFT. “Y”...
- Page 16 Double Springs Applications, Two Or Four Center bearing Torsion Equal Right hand end brackets Springs, 1 Piece Shaft, Up To 2-5/8” Springs shaft spacing bearing bracket with dodge bearing (optional) Torsion Drum keyed Left wound, black spacer shaft Coupler winding cone (right Right half hand side)
- Page 17 Up To 3-3/4” Springs Applications Stationary Torsion spring cone spring (3) 3/8” - 16 x 1-3/4” hex head screws and (3) 3/8” - 16 Hex nuts Center Stationary bracket Torsion spring cone Coupler Torsion spring assembly spring Center bracket Coupler halves Torsion (2) 3/8”-16 x 1-1/2”...
- Page 18 terminate at the 3 o’clock position. NOTE: Prior to securing the cable drum to the torsion shaft NOTE: If you have torsion keyed shaft(s), insert (1) key into the slot of both the cable drum / torsion keyed shaft, position and the slot in the torsion keyed shaft, as shown.
- Page 19 Torsion spring(s) should be wound in the direction the end coil points. Winding Bars Size Of Winding Bar Spring Inner (Steel Rods) (Inches) Diameter Used On 1/2” dia. x 18” 2” and 2-5/8” Torsion 5/8” dia. x 24” 3-3/4” spring(s) Intermediate section Spring coils...
- Page 20 cate and install rear back hangs, as shown. Perforated Angle Gauge Weight Limitations: Perforated Angle Gauge Door Balance Weight Perforated angle bolted using (2) 5/16” x 1-5/8” 2” x 2” x 12 Gauge Less Than 800 lbs. hex head lag screws to ceiling member and 1-1/4”...
- Page 21 Attaching Weather Seal NOTE: If you don’t have weather seals, then skip this step. Refer to Package Contents / Breakdown of Parts, to determine if you have weather seals. Permanently attach the weatherstrips on both door jambs and header. The weatherstrips were temporarily attached in Preparing the Opening, in the pre-installation section of this manual.
-
Page 22: Optional Installation
Optional Installation No. 6 Inside Lock Screw eye Typical bottom corner bracket Install the inside lock on the second section of the door. Secure the lock to the section with (4) 1/4” - 20 x 5/8” self drilling screws. Square the lock assembly with the door section, and align with the square hole in the vertical track. -
Page 23: Pusher Springs
WARNING Single trolley operator bracket is door size dependent. Trolley operator bracket is supplied by others. WAYNE DALTON RECOMMENDS THE USE OF A TROLLEY RAIL(S) AND AUXILIARY SHAFT FOR STANDARD OR HIGH LIFT DOORS BELOW THESE LIMITS. CABLE KEEPERS ARE RECOMMENDED FOR ALL CHAIN HOIST OR JACKSHAFTS OPERATORS. -
Page 24: Maintenance
Installation Instructions and Owner’s Manual for the garage door. These instructions are available at no charge from Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at www.Wayne-Dalton.com. For additional information on garage door/operator maintenance go to www.dasma.com and reference TDS 151, 167 and 179. -
Page 25: Warranty
Wayne Dalton, a division of Overhead Door Corporation ("Seller") warrants to the original purchaser of the Full-View Models 8450, 8850, 464, 451 or 452 Doors (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from... - Page 26 Thank you for your purchase. If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have. After installation is complete, leave this Installation Instructions And Owner’s Manual with the homeowner, or fasten it near garage door for easy reference.