Table of Contents
Advertisement
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts and the CBA in order to gain access to
items to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[3] Power Supply
[1] Rear Cover
CBA Unit
[6] Speaker
Assembly
[7] Stand Holder
[9] LCD Panel
Assembly
[10] Rear Frame
[11] LCD Module
[12] Front
Cabinet
2. Disassembly Method
Step/
Fig.
Loc.
Part
No.
No.
[1]
Rear Cover D1 9(S-1), 6(S-2)
Stand
[2]
D1 3(S-3)
Assembly
Power
D2
[3]
Supply
D5
CBA Unit
T-CON
D2
[4]
CBA
D5
Digital Main
D2
[5]
CBA Unit
D5
[6]
Speaker
D3 ---------------
Stand
[7]
D3 4(S-7)
Holder
Function
D3
[8]
CBA Unit
D5
LCD Panel
[9]
D3 ---------------
Assembly
[10] Rear Frame D4 12(S-8), 2(S-9)
LCD
[11]
D4 ---------------
Module
Front
[12]
D4 ---------------
Cabinet
↓
↓
↓
(1)
(2)
(3)
[4] T-CON CBA
[2] Stand
[5] Digital Main
CBA Unit
[8] Function
CBA Unit
Removal
5(S-4), CN1, CN2,
CN3, CN4, CN5
2(S-5), CN1001,
CN1002
4(S-6), CN9, CN23,
Jack Holder,
Shield Box
Sensor Lens
↓
(4)
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
N = Nut, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
e.g. 2(S-2) = two Screws of (S-2),
2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the
Table."
1
*
Precautions concerning the LCD Panel
Assembly:
1. When you disassemble the LCD Panel
Assembly
• Be careful not to scratch the Reflection Sheet with
the edge of Rear Frame when disassembling/
re-assembling it.
• Be careful not to drop any plastic chip on the
Reflection Sheet when/after you remove the Screws.
• Prohibit to put any external pressure on the
Reflection Sheet because the scratch on the back of
Note
the Reflection Sheet have direct repercussion on the
display screen.
---
• Prohibit to put any external pressure on the Sheet
Holder or LED Heat Sink Assembly either because it
---
also has repercussion on the display screen via the
Reflection Sheet.
---
• You need to remove any visible dust from the
Reflection Sheet which creates the external
pressure between the Reflection Sheet and the
*2
Sheet Holder/LED Heat Sink Assembly as a result.
• To prevent the Screw from being stripped, the screw
---
tightening torque should be 13.23 lbf·in(6 kgf·cm) for
the Rear Frame Screw and 5.512 lbf·in(2.5 kgf·cm)
for the LED Heat Sink Assembly Screw.
---
• Do not pull the FFC Cable and Board Cable
---
forcefully when you re-assemble.
*1
*1
*1
*1
*1
↓
(5)
4-1
A23A0DC
Advertisement
Table of Contents
