Table of Contents
Advertisement
Call waiting
When you subscribe to call waiting
service with your telephone service
provider, you hear an alert tone if there
is an incoming call while you are on
another call.
• Press FLASH to put the current call
on hold and take the new call.
• Press FLASH at any time to switch
back and forth between calls.
If you also subscribe to caller ID
service, it will let you see the name and
telephone number of the caller during
call waiting.
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provider
if:
• You have both caller ID and call
waiting, but as separate service (you
may need to combine these service);
• You have only caller ID service, or
only call waiting service; or
• You do not subscribe to caller ID or
call waiting services.
There are fees for caller ID services. In
addition, services may not be available
in all areas.
Chain dialing
Use this feature to initiate a dialing
sequence from numbers stored in the
phonebook, caller ID log or redial list
while you are on a call.
Chain dialing can be useful if you wish
to access other numbers (such as bank
account numbers or access codes)
from the phonebook, caller ID log or
redial list.
To access a number from the
phonebook while on a call:
1. Press MENU.
2. Press SELECT to select Phonebook.
3. Press
or
to scroll to the desired
entry.
4. Press SELECT to dial the displayed
number.
To access a number from the
caller ID log while on a call:
1. Press MENU.
2. Press
or
to choose Caller ID log,
and then press SELECT.
3. Press
or
to scroll to the desired
entry.
4. Press SELECT to dial the displayed
number.
To access a number from the
redial list while on a call:
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly to
browse to the desired entry.
3. Press SELECT to dial the displayed
number.
12
Find handset
This feature helps you find all system
handsets.
To start paging:
• Press /FIND HANDSET on the
telephone base.
All idle handsets ring and display
** Paging **.
To end paging:
• Press /FIND HANDSET again on
the telephone base.
-OR-
, OFF,
• Press
or any dialing key
(0-9,
or
) on the handset.
,
-OR-
• Place the handset in the telephone
base or charger.
NOTES
• Press MUTE to turn off the ringer of a
handset temporarily. Paging tone continues
on the other handset.
• Do not press and hold /FIND HANDSET
for more than four seconds. It may lead
to handset deregistration. If the handset
displays To register HS... and ...see
manual, refer to the Frequently asked
questions section to register the handset
back to the telephone base.
Redial list
Each handset stores the last
10 telephone numbers dialed. Entries
are shown in reverse chronological
order. When there are already
10 entries, the oldest entry is deleted to
make room for the new entry.
Review a redial list entry
1. Press REDIAL to enter the redial list.
, , or REDIAL repeatedly
2. Press
to browse until the desired entry
displays.
NOTE
• You hear a double beep when you reach
the beginning or end of the redial list.
Dial a redial list entry
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
3. Press
or
to dial.
-OR-
1. Press
or
to take the line.
2. Press REDIAL to enter the redial list.
3. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
4. Press SELECT to dial the displayed
number.
Delete a redial list entry
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
3. When the handset displays the number
you want to delete, press DELETE.
You hear a confirmation tone.
13
Advertisement
Table of Contents
