Page 2
FIG. 1 Limited Machine Warranty I N S T A L L A T I O N Proluxe warrants this dough press machine, when operated under normal conditions, to Domestic be free from manufacturing defects in material and workmanship for a period of ...
This warranty does not apply to any machine that has been subjected to misuse, negligence or accident. Proluxe shall not be liable for the injury, loss or damage, direct or consequential, arising out of the use or the ...
Page 4
S A F E T Y S U M M A R Y and rating fuse. Listed Supplemental Fuse rated max 3A, 120Vac. Avertissement Pour une protection continue contre l’incendie Warning et de choc électrique, remplacer avec le même To reduce the risk of electrical shock, do not ...
Page 5
If you would prefer a set of legs which would action forces the closing of the platens. raise your machine off the table 4 inches. Please contact sales at i nfo@proluxe.com for (B) Thickness control dial. a set. Shipping charges may apply. ...
Solid State Controller 4. R esetting the Counter: This controller has three (3) control features: Press MODE button until the 1. T emperature – May be set from counter is displayed. 100°-425°F (38°-163°C) Factory default is 200ºF. ...
Page 7
Tightening the Pull-down Handle Note : Heat is provided in the upper platen is only The pull-down pressing handle requires for purposes of enabling the dough to flow more adjustment periodically to prevent it from rapidly in the pressing cycle. The heat IS NOT free falling.
The lubricant use must be USDA-H-I soap and warm water will do the job quite authorized for food machinery. This lubricant nicely. can be ordered through Proluxe, part # 110-002. DO NOT use ice or cold water to cool the ...
Page 9
Endurance X2 Troubleshoot Guide - Model #: DP2000 Problem Cause Action Ref # Power button on 1. Power cord is not plugged in. 1. Plug the power cord into wall digital controller face receptacle and power button. 68 ...
Page 10
When depressing the The tactile buttons under the overlay Carefully (no too much at one tactile button on may be not close enough to activate. time to avoid fracturing the digital controller, Same goes if the buttons are already traces on the controller) tighten ...
Page 13
Endurance X2 Part List - Model #: DP2000 DP2000B DP2000LB DP2000E DP2000LE DP2000TB DP2000TLB DP2000TE DESCRIPTION 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 110178154 110178154...
Page 14
CC12 SCREW, PHILLIPS PAN HEAD 8-32 X SP83238 SP83238 SP83238 SP83238 SP83238 SP83238 SP83238 DP2000B DP2000LB DP2000E DP2000LE DP2000TB DP2000TLB DP2000TE DESCRIPTION 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC...
Page 15
110102121 BRACKET, MICRO SWITCH FITTING, ZERK 1/4-28 B792 B792 B792 B792 B792 B792 B792 DP2000B DP2000LB DP2000E DP2000LE DP2000TB DP2000TLB DP2000TE DESCRIPTION 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC...
Page 16
DP2000B DP2000LB DP2000E DP2000LE DP2000TB DP2000TLB DP2000TE DESCRIPTION 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC 240 ~ AC TERMINAL, RING #6 14-16 GA HIGH TEMP 1601HT 1601HT 1601HT 1601HT...
Cannot be canceled and are not returnable be returned after 30 days. If upon inspection unless defective within the terms of this by Proluxe or its authorized agent it is warranty. determined the equipment has not been used In no event shall Proluxe be liable for ...
Page 19
5. F r eight/Routing : Method of shipment will insurance or other levies, all of which are the be determined by Proluxe unless otherwise responsibility of the purchaser. advised by purchaser. ...