Related Manuals for Proluxe Doughpro Apex Pro X2
Summary of Contents for Proluxe Doughpro Apex Pro X2
- Page 1 Operations Manual Apex Pro X2 - Hydraulic Automatic Dough Press Model #: DP2350 WWW.PROLUXE.COM Version: 51219...
-
Page 2: Installation
Congratulations! conditions, to be free from manufacturing defects in material and Your selection of the Doughpro DP2350 workmanship for a period of one year on is a sound business decision. Doughpro parts and labor from the invoice date. equipment is a result of the highest quality engineering and time-tested This warranty will be effective only design. - Page 3 • To view the set points of temperature, timer and counter, WARNING Avoid touching hot surfaces press MODE button to view the while operating the machine. desired mode of operation. CAUTION 2. Changing Temperature: During normal operation, the • Press MODE button until base of the machine must be temperature is displayed.
-
Page 4: Additional Notes
5. Place your pre-portioned ball of 1. Switch the DP2350 to the ON dough in the approximate center position. of the lower platen. Add another dash of spray to the top of the Note: Initial temperature setting of dough ball. 150°F has been shown to be acceptable for most dough formulations;... - Page 5 International Symbols Contact our factory or approved service agency (800) 624-6717 (U.S. only). Note: When contacting factory for information, parts or service instructions, it is of the utmost importance that the serial number of the machine be provided. This number can be found on the serial plate located on the rear of the machine.
- Page 6 DOUGHPRO DP2350 Automatic Air Press Trouble Shooting Guide Symptom Probable Cause Action to be Taken Ref. #'s on Explosion Drawing Power Button on Digital Controller Power Cord is not plugged in. Plug power cord into wall 's face is depressed but doesn’t turn receptacle and depress power button on controller Circuit Breaker is tripped off in the...
- Page 7 DOUGHPRO DP23 0 Automatic Air Press Trouble Shooting Guide Symptom Probable Cause Action to be Taken Ref. #'s on Explosion Drawing If setpoint is reached but slighty off Offset may need to be calibrated and Must call (800) 624-6717 ext. 129 in temperature.
- Page 8 EXPLOSION VIEW DP2350E (EL/ER) 11/05/19 127 2X 93 2X 113 3X 121 2X 33 4X 47 4X 32 2X 117 2X 14 4X 33 4X 74 2X 51 2X 36 2X 60 3X EXPDP2350E (EL/ER) RD 110519 CUSTOMER MANUAL...
- Page 9 110 2X 14 2X 45 4X EXPDP2350E (EL/ER) RD 110519 CUSTOMER MANUAL 46 4X...
- Page 10 PROLUXE PARTS LIST FOR DP2350E (EL/ER) DP2350E ITEM # DESCRIPTION QTY. 208 ~ AC BASE AND POST WELDING ASSEMBLY, DP2350E DP21002 PISTON GUIDE WELDING ASSEMBLY (DP2350/DP2350M) DP13904 CYLINDER, HYDRAULIC - 40 MM BORE x 1.687 STROKE DP13140 MOUNTING PLATE DP13105...
- Page 11 PROLUXE PARTS LIST FOR DP2350E (EL/ER) DP2350E ITEM # DESCRIPTION QTY. 208 ~ AC DIGITAL CONTROL REV. 5.06 DP139052 BOTTOM COVER DP13154 PAN HEAD SLOTTED 8-32 X 3/8" PLATED SPS83238 FEET, RUBBER RF209 NYLON SPACER, 1/4 X .141 X 9/32 LONG 110969111 WASHER, .311 OD X .150 ID X .20 THK...
- Page 12 PROLUXE PARTS LIST FOR DP2350E (EL/ER) DP2350E ITEM # DESCRIPTION QTY. 208 ~ AC TERMINAL, QD 3/16 x 18-22 GA (PINK) 2280 14- 16 GA #10 FORK TERMINAL ISUL. 1626 TERMINAL, RING #8 14-16 GA (BLUE) 1604 RTD SENSOR ASSEMBLY...
- Page 13 PROLUXE PARTS LIST FOR DP2350E (EL/ER) DP2350E ITEM # DESCRIPTION QTY. 208 ~ AC WIRE, 14 GA. RED, 41 STRAND WR1441 .83 FT SCREW, SET 5/16-18 x 3/8 SET SCREW KNURLED CUP POINT SST5161838KN CRANK HANDLE, ADJUSTMENT 1106001 SCREW BUTTON HEAD 3/8-16 X 3/4"...
-
Page 15: Warranty And Return Policy
Exclusions: 1. WOOD / GAS FIRED OVENS: PROLUXE warranty applies to the main body of the oven being steel / refractory and insulation shall be free from defects in materials and workmanship for a period of four years from the date of purchase. The gas equipment shall be free from defects in materials and workmanship for a period of one (1) year from the date of purchase.