Electrical Specifications - Delta DVP-SX2 Instruction Manual

 Electrical Specifications
Model
Item
Power supply voltage
Inrush current
Fuse capacity
Power consumption
Insulation resistance
Noise immunity
Grounding
Operation / storage
Vibration / shock
resistance
Weight (g)
Spec.
Items
Input No.
Input type
Input Current (± 10%)
Input impedance
OffOn
Action level
OnOff
OffOn
Response
time OnOff
Filter time
Spec.
Items
Output No.
Max. frequency
Working voltage
Resistive
Max. load
Inductive
Lamp
OffOn
Response
time
OnOff
#1: DVP20SX211T: UP, ZP must work with external auxiliary power supply 24VDC (-15% ~
+20%), rated consumption approx. 3mA/point.
DVP20SX211S: UP, ZP must work with external auxiliary power supply 5~30VDC, rated
consumption approx. 5mA/point.
#2: Life curves
DVP20SX211R
24VDC (-15% ~ 20%)
(with counter-connection protection on the polarity of DC input power)
DVPPS01(PS02): input 100-240VAC, output 24VDC/1A(PS02: 2A)
Max. 7.5A@24VDC
2.5A/30VDC, Polyswitch
4.7W
> 5MΩ (all I/O point-to-ground: 500VDC)
ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV,
Analog & Communication I/O: 1kV
RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
Surge(IEC 61131-2, IEC 61000-4-5) :
DC power cable: differential mode ±0.5 kV
analog I/O, RS-232, USB (shielded): Common mode ±1 kV
digital I/O, RS-485 (unshielded): Common mode ±1 kV
The diameter of grounding wire cannot be smaller than the wire
diameter of terminals 24V and 0V (All DVP units should be grounded
directly to the ground pole).
Operation: 0°C ~ 55°C (temp.), 50 ~ 95% (humidity), Pollution degree2
Storage: -25°C ~ 70°C (temp.), 5 ~ 95% (humidity)
International standards: IEC61131-2, IEC 68-2-6 (TEST
Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
243g
24VDC (-15% ~ 20%) single common port input
X0, X2
< 2.5μs
< 5μs
Adjustable within 0 ~ 20ms by D1020 (Default: 10ms)
Relay
Y0 ~ Y5
1Hz
250VAC, < 30VDC
1.5A/1 point (5A/COM)
#2
20WDC/100WAC
Approx. 10 ms
120VAC Resistive
3000
30VDC Inductive(t= 7ms)
2000
1000
500
300
200
100
30VDC
Inductive
50
(t=40ms)
0.1
0.2
0.3 0.5
DVP20SX211T
4W
224g
Input Point
X1, X3
DC (SINK or SOURCE)
24VDC, 5mA
4.7K Ohm
> 15VDC
< 5VDC
< 10μs
< 20μs
Output Point
Y0, Y2
100kHz
SX211T: 0.5A/1 point (3A/ZP)
SX211S: 0.3A/1 point (1.8A/UP)
2μs
3μs
240VAC Inducti ve(cos
ψ
120VAC Inductive(cos =0.4)
Contact
Current(A)
0.7 1 2
- 2 -
DVP20SX211S
X4 ~ X7
Transistor
Y1, Y3
10kHz
#1
5 ~ 30VDC
15W (30VDC)
2.5W (30VDC)
20μs
30μs
= 0.4)
ψ
[ Figure 3 ]
4W
227g
< 20us
< 50us
Y4, Y5
1kHz
100μs
100μs