Download Print this page

Advertisement

Available languages

Available languages

Quick Links

2014-01-22
5012617102-3202

Advertisement

loading
Need help?

Need help?

Do you have a question about the DVP32ES200RC and is the answer not in the manual?

Questions and answers

Polius Actie
June 10, 2025

Delta PLC DVP-32ES is equipped with how many sockets?

Summary of Contents for Delta DVP32ES200RC

  • Page 1 2014-01-22 5012617102-3202...
  • Page 2 ………………………………………………………………… ………………………………………………………………… Thank you for choosing Delta’s DVP-ES2 series PLC. DVP-ES2 series MPU provides 32 points (16 points digital Input, 16 points digital Output and built-in CANopen). The maximum I/O points including those on the MPU are 256 points. DVP-ES2 series PLCs satisfy various applications in that they can be used with analog input/output modules.
  • Page 3: Electrical Specifications

    Electrical Specifications Model DVP32ES200RC DVP32ES200TC Item Power supply 50/60Hz ±5% 100 ~ 240VAC (-15% ~ 10%) voltage Connector European standard removable terminal block (Pin pitch: 5mm) DVP-ES2 starts to run when the power rises to 95 ~ 100VAC and stops Operation when the power drops to 70VAC.
  • Page 4: Installation

    Station address 1~127 Electrical isolation 500V DC Users are suggested to use the Delta standard cable TAP-CB01 Communication cable or TAP-CB02, and the communication cable should be kept away from the power cable. ON: (Default) Communication is enabled. Control flag M1349 OFF: Communication is disabled.
  • Page 5: Safety Wiring

    3. Use 1.6mm wire (or longer) for the grounding of the PLC. 4. The power shutdown of less than 10ms will not affect the operation of the PLC. However, power shutdown time that is too long or the drop of power supply voltage will stop the running of the PLC, and all outputs will go “OFF”.
  • Page 6 Relay (R) output circuit wiring [ Figure 7 ] ○ ○ DC power supply Emergency stop: Uses external switch Fuse: Uses 5 ~ 10A fuse at the shared terminal of output contacts to protect the output ○ circuit Transient voltage suppressor: To extend the life span of contact. ○...
  • Page 7 PLC Tr an sisto r PLC Tr an sisto r ou tpu t ou tpu t Lar ge r po wer a nd Sma ller p ower f req ue nt on /of f Z D D D: 1N4 00 1 diod e or equ ivale nt co mpo ne nt D: 1N4 001 diod e or equ ivale nt co mpo nen t Z D: 9V Ze ner , 5W [ F ig ure 1 2 ]...
  • Page 8 Error states of slaves D9998 (bit0~15: Slave 1~Slave 16; ON: An error occurs.) Note: Please refer to DVP-ES2/EX2/SS2/SA2/SX2/SE Operation Manual for more information about the CANopen communication. I/O Terminal Layouts DVP32ES200RC, DVP32ES200TC +24V DVP32ES2-R (16DI/16DO) CAN- CAN+ +24V DVP32ES2-T (16DI/16DO)
  • Page 9 COM 2 (RS-4 85) 直接固 定孔 DIN 軌固定扣 脫落式 輸出/入 端子 詳細尺寸圖請參閱英文版[Figure 2],單位:mm。 電氣規格 機種 DVP32ES200RC DVP32ES200TC 項目 電源電壓 100 ~ 240VAC (-15% ~ 10%),50 / 60Hz ± 5% 連接方式 脫落式歐式端子座 (端點距離:5mm) 當電源緩升至 95 ~ 100VAC 時 , PLC 開始動作 , 當電源緩降至 70VAC 時,...
  • Page 10 機種 DVP32ES200RC DVP32ES200TC 項目 ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, 雜訊免疫力 Analog & Communication I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m 接地配線之線徑不得小於電源端 L, N 之線徑(多台 PLC 同時使用時,請...
  • Page 11 站號設定範圍 1~127 電氣隔離 500V DC 建議使用台達標準電纜 TAP-CB01 或 TAP-CB02 電纜,其通訊電纜須遠離 通訊電纜 電力電纜 控制旗標 ON(預設值)表示啟動通訊,OFF 表示關閉通訊 註 1:作為主站時所連接的從站站號僅可設置為 1~16,主從站的站號不能重複。 註 2:CANopen 網路功能需透過 CANopen Builder 軟體進行設定,詳細設定請參考軟體說明書。 安裝方式 PLC 在安裝時,請裝配於封閉式之控制箱內,其 周圍應保持一定之空間 (如圖所示) , 以確保 PLC 散熱功能正常。 直接鎖螺絲方式:請依產品外形尺寸並使用 M4 螺絲。 DIN 鋁軌之安裝方法:適用於 35mm 之 DIN 鋁軌。在將主機掛上鋁軌時,請先將主機 (或數位輸入/輸出模組)...
  • Page 12 直流電源供應輸出:24VDC,500mA 接地阻抗 100Ω 以下 ○ ○ 直流電源供應:24VDC 數位輸入/輸出模組(直流供應) ○ ○ 數位輸入/輸出模組(交流供應) 類比輸入/輸出模組(直流供應) ○ ○ 直流電源供應:20.4VDC ~ 28.8VDC ○ 輸入⁄輸出點之配線 輸入點之入力信號為直流電源 DC 輸入,DC 型式共有兩種接法:SINK 及 SOURCE,其 定義如下: (以下為舉例說明,詳細點數配置請見各機種) 直流形式(DC Signal IN)配線 – SINK 模式 輸入點回路等效電路配線圖,請參閱英文版[Figure 5]。 直流形式(DC Signal IN)配線 – SOURCE 模式 輸入點回路等效電路配線圖,請參閱英文版[Figure 6]。...
  • Page 13 CANopen(COM3)通訊燈號指示說明 LED 燈狀態 顯示說明 處理方法 綠燈常亮 DVP32ES200TC 處 無需處理 於正常狀態 綠燈單閃 DVP32ES200TC 處 上位機正在下載程式,等待下載完成 (每 1 秒亮 1 次) 於停止狀態 綠燈閃爍 從站時處於預運行 1. 檢查 CANopen 匯流排連接線纜是否為標準線纜 狀態 2. 檢查 CANopen 網路中匯流排線纜接線是否正確 3. 檢查主從站的傳輸速率是否相同 主站時處於預連接 1. 檢查 CANopen 匯流排線纜是否為標準線纜 狀態 2. 檢查 CANopen 網路中匯流排線纜接線是否正確 3.
  • Page 14 16 DI /1 6DO (35 mm) COM 3 (CAN open) COM 2 (RS-4 85) 详细尺寸图请参阅英文版[Figure 2],单位:mm。 电气规格 机种 DVP32ES200RC DVP32ES200TC 项目 电源电压 100 ~ 240VAC (-15% ~ 10%),50 / 60Hz ± 5% 连接方式 脱落式欧式端子座 (端点距离:5mm) 当电源缓升至 95 ~ 100VAC 时, PLC 开始动作, 当电源缓降至 70VAC 时,...
  • Page 15 机种 DVP32ES200RC DVP32ES200TC 项目 ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, 噪声免疫力 Analog & Communication I/O: 1kV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m 接地配线之线径不得小于电源端 L, N 之线径(多台 PLC 同时使用时,请...
  • Page 16 站号设定范围 1~127 电气隔离 500V DC 建议使用台达标准电缆 TAP-CB01 或 TAP-CB02 电缆, 其通讯电缆须远 通讯电缆 离电力电缆 控制旗标 M1349 ON(默认值)表示启动通讯,OFF 表示关闭通讯 注 1:作为主站所连接的从站站号仅可设置为 1~16,主从站的站号不能重复。 注 2:CANopen 网络功能需透过 CANopen Builder 软件进行设定,详细设定请参考软件说明书。 安装方式 PLC 在安装时,请装配于封闭式的控制箱内,其 周围应保持一定的空间 (如图所示) , 以确保 PLC 散热功能正常。 直接锁螺丝方式:请依产品外形尺寸并使用 M4 螺丝。 DIN 铝轨的安装方法:适用于 35mm 的 DIN 铝轨。在将主机挂上铝轨时,请先将主机 (或数字量输入/输出模块)下方的固定塑料片,以一字形起子插入凹槽并向外撑开拉...
  • Page 17 ○ 电源回路保护用保险丝(2A) ○ DVP PLC 主机本体 ○ 直流供应电源输出:24VDC,500mA ○ 接地阻抗 100Ω 以下 直流供应电源:24VDC 数字量输入/输出模块(直流供应) ○ ○ 数字量输入/输出模块(交流供应) 模拟量输入/输出模块(直流供应) ○ ○ ○ 直流电源供应:20.4VDC ~ 28.8VDC 输入/输出点之配线 输入点的接入信号为直流电源 DC 输入,DC 型式共有两种接法:漏型及源型,其定义如 下: (以下为举例说明,详细点数配置请见各机种) 直流形式(DC Signal IN)配线 – 漏型模式 输入点回路等效电路配线图,请参阅英文版[Figure 5]。 直流形式(DC Signal IN)配线 – 源型模式 输入点回路等效电路配线图,请参阅英文版[Figure 6]。...
  • Page 18 RS-485(COM2)建议接线 详细接线图请参阅英文版[Figure 15]。 主站 从站 终端电阻 屏蔽线 ○ ○ ○ ○ 附注:1. 终端电阻建议连接于主站及最后一台从站上,且其阻值建议为 120Ω。 2. 为确保联机质量,线材建议使用具有双层屏蔽线的通讯双绞线(20AWG)。 CANopen(COM3)通讯灯号指示说明 LED 灯状态 说明 处理方法 无需处理 DVP32ES200T 绿灯常亮 C 处于正常状态 绿灯单闪 上位机正在下载网络配置,等待下载完成 DVP32ES200T C 处于停止状态 (每 1 秒亮 1 次) 1. 检查 CANopen 总线线缆是否为标准线缆 从站时处于预...

This manual is also suitable for:

Dvp32es200tc
Save PDF