Specifications - Makita HM1101C Instruction Manual

ENGLISH (Original instructions)
1-1. Switch lever
2-1. Adjusting dial
3-1. Power-ON indicator lamp (green)
3-2. Service indicator lamp (red)
4-1. D-shaped side handle
4-2. Clamp nut
5-1. Side grip (auxiliary handle)
6-1. Bit shank

SPECIFICATIONS

Blows per minute
Net weight with D-shaped side handle
Net weight with side grip
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for chiselling work in concrete, brick,
stone and asphalt as well as for driving and compacting
with appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model HM1111C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model HM1101C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Explanation of general view
6-2. Bit grease
7-1. Releasing cover
9-1. Releasing cover
10-1. Change ring
14-1. Screws
15-1. Connector
15-2. White
15-3. Black
Model
Overall length
Safety class
) : 88 dB(A)
pA
) : 99 dB(A)
WA
) : 90 dB(A)
pA
) : 101 dB(A)
WA
HM1111C
528 mm
8.0 kg
7.8 kg
ENE045-1
Model HM1111C
Work mode : chiseling function with side handle
Vibration emission (a
Uncertainty (K) : 1.5 m/s
ENF002-1
Work mode : chiseling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model HM1101C
Work mode : chiseling function with side handle
ENG905-1
Vibration emission (a
Uncertainty (K) : 2.0 m/s
Work mode : chiseling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
ENG900-1
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
4
16-1. Screwdriver
16-2. Crank cap
17-1. Grease
18-1. Connector
18-2. White
18-3. Black
HM1101C
-1
1,100 - 2,650 min
528 mm
7.3 kg
7.2 kg
II
2
) : 7.5 m/s
h,CHeq
2
2
) : 8.0 m/s
h,CHeq
2
) : 13.5 m/s
h,CHeq
2
) : 13.5 m/s
h,CHeq
2
2
2
ENG901-1