Windsor SABER GLIDE 10053070 Operating Instructions Manual page 84

9150 SCRUB DECK-36 IN MAIN
POS Article no. Description
1 8.627-691.0 SCREW, 5/16-18 X 3 HHCS SS NP
2 8.600-155.0 HOSEBARB, 3/8MPT X3/8 90D
3 8.627-396.0 SCREW, 1/4-20 X 3 HHCS SS
4 8.600-084.0 ACTUATOR ASM, SRS
5 8.600-525.0 Motor complete 36V 330 RPM GEAR
5 8.600-189.0 X-REF 140394 OBS 10/04
6 8.622-347.0 RING, 20MM EXTERNAL SNAP
7 8.627-183.0 NUT, 3/8-16 LK NYL BLK
8 8.625-325.0 SHAFT, PIVOT
9 8.627-262.0 PIN, CLEVIS 1/4 X 1.125 STL ZNPLT
10 8.600-757.0 Spring GAS 300 NEWTONS
11 8.625-650.0 STUD, BALL GAS SPRING
12 8.627-083.0 NUT, 5/16-18 HEX NYLOCK SS
13 8.623-617.0 FITTING, 1/2 MPT X 3/8 BARB 90
14 8.619-791.0 Hosebarb 1/2MPT X 1/2 POLY DL
15 8.603-322.0 MANIFOLD, SOLUTION FEED SRS
16 8.626-492.0 CABLE TIE, 7" UL/CSA
17 8.628-141.0 HOSE, 3/8ID NYLOBRD X 7.5"
18 8.628-148.0 HOSE, 1/2" ID NYLOBRD X 14"
19 8.600-920.0 KNOB, 3/8-16 4 PRONG ALUM
20 8.627-411.0 SCREW, 1/4-20 X .5 SCHCS SS
21 8.601-079.0 WASHER, 3/8 SPL STL ZNPLT
22 8.627-697.0 SCREW, 3/8-16 X .75 HHCS SS
23 8.627-695.0 SCREW, 1/4-20 X .75 CARR SS
24 8.600-741.0 SKIRT, FRONT 36" DECK
25 8.608-790.0 STRAP, FRONT SKIRT
26 8.600-581.0 NUT, 1/4-20 HEX NYLOCK SS
27 8.600-702.0 SCREW, 5/16-18 X 1.25 HHCS SS NP
28 8.627-913.0 WASHER, 5/16 SPLT STL ZNPLT
29 8.627-963.0 WASHER, 5/16 X 1.13 X .09 FLT
30 8.600-342.0 DRIVER, BRUSH SD
31 8.627-953.0 WASHER, .765 X 1.312 X .09 SS
32 8.609-397.0 SCRUB DECK , 36" MIN
Valid on 05.10.2018 Page 40 / 97
Quantity Unit
1.000 ST
2.000 ST
1.000 ST
1.000 ST
2.000 ST
1.000 ST
2.000 ST
2.000 ST
2.000 ST
1.000 ST
1.000 ST
2.000 ST
5.000 ST
3.000 ST
1.000 ST
1.000 ST
2.000 ST
2.000 ST
1.000 ST
1.000 ST
1.000 ST
8.000 ST
8.000 ST
6.000 ST
1.000 ST
1.000 ST
8.000 ST
2.000 ST
2.000 ST
2.000 ST
2.000 ST
2.000 ST
1.000 ST