Related Manuals for Cardinal RD3
Summary of Contents for Cardinal RD3
- Page 1 Remote Display Installation and Technical Manual 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
- Page 2 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 3: Table Of Contents
…………..………..…......Page 18 Rear Sub-Assembly …………..………..…......Page 20 Front Sub-Assembly PRECAUTIONS Before using this instrument, read this manual and pay special attention to all "WARNING" symbols: ELECTRICAL STATIC IMPORTANT WARNING SENSITVE 8200-M063-O1 Rev C RD3 Installation and Technical Manual... - Page 4 Seller is not able to guarantee the result of any procedure contained herein. Nor can they assume responsibility for any damage to property or injury to persons occasioned from the procedures. Persons engaging in the procedures do so entirely at their own risk. 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 5: Introduction
INTRODUCTION Thank you for your purchase of our Cardinal RD3 Remote Display. It was built with Cardinal quality and reliability. This manual will guide you through the installation, and operation of your display. Please read it thoroughly before attempting to install your display. Also, make certain that you pay attention to the warnings that appear in this manual. -
Page 6: Auto-Format Feature
SITE PREPARATION Electrical Power The RD3 display has been designed to operate from 100 to 240V AC at 47/63 Hz. CAUTION! To avoid electrical hazards and possible damage to the display, DO NOT, under any circumstance, cut, remove, alter, or in any way bypass the power cord-grounding prong. -
Page 7: Single And Multiple Displays
The RD3 display has been designed to echo received characters (from a single weight indicator) to other RD3 displays allowing the same weight data to be shown on multiple displays. Typical applications might consist of back-to-back displays or displays placed at each end of the scale. - Page 8 SINGLE AND MULTIPLE DISPLAY, CONT. Figure No. 3 – Multiple RD3 Displays 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 9: Installation
Mounting the RD3 Display The RD3 Display includes a two-piece bracket that is used to mount it on a wall or other flat vertical surface using a quick-detach bracket. Note that the Display Bracket is installed on the RD3 at the factory. -
Page 10: Serial Cable Installation
7. Repeat the procedure until all wires are in place. 8. After all, terminations have been made, remove any excess cable from the enclosure, and securely tighten the cable gland connector. Finger-tighten only! DO NOT USE TOOLS! 8200-M063-O1 Rev C RD3 Installation and Technical Manual... -
Page 11: Rs232 Wiring
Figure No. 7 Figure No. 8 RD3 PASSIVE END RD3 ACTIVE END IMPORTANT! A jumper must be installed between P4 terminals 1 and 7 to enable 20mA current loop operation. 8200-M063-O1 Rev C RD3 Installation and Technical Manual... -
Page 12: Current Cardinal Indicators 20Ma Current Loop Connections
P13, 8 P4, 6 P13, 9 P4, 9 JUMPER JUMPER JUMPER P13, 9 to P13, 10 P4, 1 to P4, 7 P4, 4 to P4, 5 JUMPER P4, 1 to P4, 7 8200-M063-O1 Rev C RD3 Installation and Technical Manual... - Page 13 P4, 6 P21, 2 P4, 9 J3 INSTALLED JUMPER J3 REMOVED JUMPER P4, 1 to P4, 7 J7 SHUNT:20mA J7 SHUNT:20mA P4, 4 to P4, 5 JUMPER P4, 1 to P4, 7 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 14: Legacy Cardinal Indicators 20Ma Current Loop Connections
P4, 1 to P4, 7 P4, 4 to P4, 5 JUMPER P4, 1 to P4, 7 PORT 2 P10, 11 P4, 5 P10, 10 P4, 6 JUMPER P4, 1 to P4, 7 8200-M063-O1 Rev C RD3 Installation and Technical Manual... - Page 15 COMA, 23 P4, 9 COMA, 11 P4, 6 JUMPER JUMPER JUMPER P4, 4 to P4, 5 COMA, 23 to COMA, 24 P4, 1 to P4, 7 JUMPER P4, 1 to P4, 7 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 16: Display Board
DISPLAY BOARD Figure No. 9 8200-M063-O1 Rev C RD3 Installation and Technical Manual... -
Page 17: Jumpers
20mA Transmitter Output (-) RxD-20mA (SRC) Source (SRC) voltage for active 20mA Receiver RxD-20mA + 20mA Receiver Input (+) RxD-20mA - 20mA Receiver Input (-) RxD-RS232 RS232 Receiver Input TxD-RS232 RS232 Transmitter Output Ground 8200-M063-O1 Rev C RD3 Installation and Technical Manual... -
Page 18: Setup And Configuration
SETUP AND CONFIGURATION The RD3 display has been pre-configured at the factory and should not require configuration for use in most applications. If the factory settings do not meet the requirements of your application, the following describes the steps to configure the display. - Page 19 Setup Complete Press the SETUP switch to save the settings. Setup and configuration have been completed. The RD3 will reset. Follow the instructions on the next page to re-install the front panel and proceed with normal operations. 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 20: Re-Installing The Front Panel
Follow a diagonal pattern when tightening the screws. ERROR AND STATUS DISPLAYS The RD3 Remote Display is equipped with software that tests various portions of its circuitry and verifies proper operation. Should a problem be detected, a message will be displayed. The... -
Page 21: Parts Identification
PHIL. DR. BLACK OXIDE WASHER FLAT .345 OD, 0.218 ID, 0.032 THK 6024-0141 NYLON 8200-D629-2A REAR SUB-ASSEMBLY: RD3 8200-D630-3A FRONT SUB-ASSEMBLY: RD3 6980-0014 CABLE TIE 4" WHITE Not Shown 8200-M063-O1 Rev C RD3 Installation and Technical Manual... -
Page 22: Rear Sub-Assembly
PART IDENTIFICATION, CONT. Rear Sub-Assembly Backside of Power Supply and Cover 8200-M063-O1 Rev C RD3 Installation and Technical Manual... - Page 23 LABEL: AC POWER TERM. BLOCK 8200-B212-0A CABLE: GROUND 205/210 8200-B237-0A CABLE: AC POWER W/FILTER 205/210 DW1 8200-B636-0A CABLE: POWER SUPPLY OUTPUT 8200-C615-08 POWER SUPPLY COVER 8200-D608-38 ENCLOSURE: PLASTIC, RD3 LABEL: WARNING HIGH VOLTAGE 8510-C346-0I 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
-
Page 24: Front Sub-Assembly
6680-0004 WASHER LOCK INT TOOTH #6 TYPE A Z-PL 6680-0131 SPACER # 6 x .400 NYLON 8200-C609-0A FRONT PLATE 8200-C611-08 OVERLAY: RD3 8200-C618-08 GASKET 8200-D600-2A PCB ASS'Y RD3 2" REMOTE DISPLAY 8200-M063-O1 Rev C RD3 Installation and Technical Manual... - Page 25 1, 2, 3, 5, 6 SCALES YEAR A, B, C, D, E, F (Including Belt-Way) 07/2023 Printed in USA 102 East Daugherty St. l Webb City, MO 64870 l (800) 441-4237 l cardinal@cardet.com l www.CardinalScale.com 315-WARRANTY-CAR-M - Page 1 -...
- Page 26 11. PSC models’ warranty coverage applies only to agricultural installations on farms up to 3,000 acres (LSC models not limited in this manner). 12. Load cell kits MUST be installed in accordance with Cardinal Scale instructions. Failure to follow these instructions will void the warranty.
- Page 27 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
- Page 28 Cardinal Scale Mfg. Co. 102 E. Daugherty, Webb City, MO 64870 USA Ph: 417-673-4631 or 1-800-641-2008 Fax: 417-673-2153 www.cardinalscale.com Technical Support: 1-866-254-8261 E-mail: tech@cardet.com Printed in USA 8200-M640-O1 Rev C 08/23 8200-M063-O1 Rev C RD3 Installation and Technical Manual...
Need help?
Do you have a question about the RD3 and is the answer not in the manual?
Questions and answers