Table of Contents
Advertisement
Quick Links
Digital
Digital
AR-C160
DIGITAL FULL COLOR
DIGITAL FULL COLOR
COPYING MACHINE
COPYING MACHINE
KEY OPERATOR
KEY OPERATOR
KEY OPERATOR CODE
KEY OPERATOR CODE
NUMBER
NUMBER
KEY OPERATOR
KEY OPERATOR
PROGRAMS
PROGRAMS
KEY OPERATOR
KEY OPERATOR
ASSISTANCE CALL
ASSISTANCE CALL
MODEL
,
,
S GUIDE
S GUIDE
Page
Page
2
2
4
4
35
33
Advertisement
Table of Contents
Related Manuals for Sharp AR-C160
Summary of Contents for Sharp AR-C160
- Page 1 Digital Digital MODEL AR-C160 DIGITAL FULL COLOR DIGITAL FULL COLOR COPYING MACHINE COPYING MACHINE KEY OPERATOR KEY OPERATOR S GUIDE S GUIDE KEY OPERATOR CODE KEY OPERATOR CODE NUMBER NUMBER KEY OPERATOR KEY OPERATOR PROGRAMS PROGRAMS KEY OPERATOR KEY OPERATOR...
-
Page 3: Table Of Contents
This KEY OPERATOR’S GUIDE contains information on all of the programs for use by the key operator. The programs allow the key operator to tailor many functions of the AR-C160 for specific modes of operation. These programs can only be accessed after a key operator code number has been entered. -
Page 4: Key Operator Code Number
- - - - - Enter 0 five times using the 10-key pad. As each 0 is entered, the dashes in the display will change to asterisks. Press the “COPIER” key on the touch panel. Press the “OTHER FUNCTION SETTINGS” key. EXIT... - Page 5 KEY OPERATOR PROGRAMS OTHER FUNCTION SETTINGS KEY OPERATOR CODE NUMBER CHANGE C:3.5 EXPOSURE ADJUSTMENT B:3.5 TONER SAVE MODE(B/W) ADD OR CHANGE EXTRA PRESET RATIOS INFORMATION INTERRUPT CUSTOM SETTINGS CLEAR AUDIT PROGRAM CLEAR KEY OPERATOR PROGRAMS KEY OPERATOR CODE NUMBER CHANGE INPUT A NEW CODE NUMBER AND PRESS [OK].
-
Page 6: Key Operator Programs
A complete list of all key operator programs is provided below. These programs can only be accessed by first entering the key operator code number. The copier key operator programs are grouped into four categories: account control, other function settings, timer settings, and enable/disable settings. - Page 7 Cancels limit control of operation in case of bin capacity overflow of an optional staple sorter. Sets a time interval after which the copier enters the sleep mode after copying is completed. Sets a time interval after which the copier returns to the initial settings.
- Page 8 PC/modem without key operator code entry. Disables the sleep mode. Disables pre-scan in black/white copying. Recalls the total counts, including counts of the copier, document feeder, duplex module, and stapler. Sequentially prints available key operator programs. becomes misadjusted. Function Enables or disables paper size detection for the bypass tray.
-
Page 9: Using The Key Operator Programs
- - - - - Enter the key operator code number. The dashes in the display will change to asterisks. Press the “COPIER” key or the “PRINTER” key on the touch panel. To access the copier key operator programs, press the “COPIER”... - Page 10 KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS COPIER MODE OTHER FUNCTION TIMER SETTINGS SETTINGS ENABLE/DISABLE ACCOUNT CONTROL SETTINGS AUTO COLOR CALIBRATION KEY OPERATOR PROGRAMS ACCOUNT CONTROL AUDITING MODE NUMBER OF COPIES PER ACCOUNT BILLING BY ACCOUNT RESETTING ACCOUNT CLEAR PROGRAM CLEAR Select the desired category on the touch panel.
-
Page 11: Account Control
ACCOUNT CONTROL The programs of this category are used to set the internal auditor functions. These programs can be selected by pressing the “ACCOUNT CONTROL” key and then selecting the desired program key. Auditing Mode This program is used to enable or disable the basic auditing mode. The auditing mode can be set for both the color and black/white (B/ W) copy modes and for only the color copy mode. - Page 12 KEY OPERATOR PROGRAMS Number of Copies per Account This program is used to display or print the total number of copies made against each account number in the color copy mode and B/W copy mode respectively. An 11" x 17" or a 12" x 18" copy is counted as two copies. When the “NUMBER OF COPIES PER ACCOUNT”...
- Page 13 Billing by Account This program is used to display or print the accumulated cost of copies made when a relevant price per copy has been set using program “Price/Copy Setting”. When the “BILLING BY ACCOUNT” key is pressed, the following display will appear.
-
Page 14: Resetting Account
KEY OPERATOR PROGRAMS Resetting Account This program is used to reset all audit accounts or to selectively reset individual accounts. When the “RESETTING ACCOUNT” key is pressed, the following display will appear. KEY OPERATOR PROGRAMS RESETTING ACCOUNT ACCOUNT COPY NUMBER OF NUMBER MODE COPIES MADE MAXIMUM... -
Page 15: Account Number Control
Account Number Control This program is used to register accounts, delete accounts, change an account number, or print all account numbers. When the “ACCOUNT NUMBER CONTROL” key is pressed, the following display will appear. KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAMS ACCOUNT NUMBER CONTROL ENTER DELETE... - Page 16 Press the “OK” key twice to exit the program. To print all registered account numbers Press the “PRINT” key. The copier will start printing. To stop printing after starting, press the “CANCEL” key. Press the “OK” key to exit the program.
- Page 17 KEY OPERATOR PROGRAMS Similarly enter the prices for price codes #2 to #4. The following display will appear. KEY OPERATOR PROGRAMS PRICE/COPY SETTING PRICE CODE PRESENT PRICE 100.000 ACCOUNT NUMBER MODE COLOR ALL ACCOUNTS Enter the account number for which the price code is set, and then press the “ENTER”...
-
Page 18: Account Limit Setting
KEY OPERATOR PROGRAMS Account Limit Setting This program is used to set the maximum number of copies which can be made against a registered account number. When the “ACCOUNT LIMIT SETTING” key is pressed, the following display will appear. KEY OPERATOR PROGRAMS ACCOUNT LIMIT SETTING INPUT ACCOUNT NUMBER TO BE LIMITED. -
Page 19: Account Number Security
If this program is selected and an operator enters three successive invalid account numbers, the copier will not accept another number for one minute and the message “PLEASE SEE YOUR KEY OPERATOR FOR ASSISTANCE.”... -
Page 20: Exposure Adjustment
KEY OPERATOR PROGRAMS OTHER FUNCTION SETTINGS The programs of this category are used to adjust various settings of copier functions. These programs can be selected by pressing the “OTHER FUNCTION SETTINGS” key and then selecting the desired program key. Key Operator Code Number Change See page 2, KEY OPERATOR CODE NUMBER. -
Page 21: Add Or Change Extra Preset Ratios
Add or Change Extra Preset Ratios Two extra preset copy ratios can be added within both the reduction range (25% to 99%) and the enlargement range (101% to 400%). Only added preset copy ratios can be changed. The standard preset copy ratios are fixed in memory and cannot be changed. -
Page 22: Initial Margin Shift Setting
KEY OPERATOR PROGRAMS Initial Margin Shift Setting Set the initial margin shift value with this program. When the “INITIAL MARGIN SHIFT SETTING” key is pressed, the following display will appear. Erase Width Adjustment Set the initial setting of the amount of the erase area with this program. When the “ERASE WIDTH ADJUSTMENT”... - Page 23 Initial Status Setting The copier will assume the initial settings when it is turned on, when the CLEAR ALL key is pressed, or when the auto clear interval has elapsed after a copy run. Use this program to establish the initial settings.
- Page 24 KEY OPERATOR PROGRAMS Initial Color Balance Setting Color balance settings that have been adjusted using the special function of “Color Balance” explained on page 3-22 of the Operation Manual can be called up and set as initial color balance settings* by storing them ahead of time in a job program (page 2-18 of the Operation Manual).
- Page 25 Require Key Operator Code This program is used to prevent the copier from being started by people other than key operator. If this program is set, the message “ENTER KEY OPERATOR CODE. -----” will appear each time the power switch is turned to the “ON” position.
-
Page 26: Stream Feeding Mode
KEY OPERATOR PROGRAMS Stream Feeding Mode This program is only available when the optional RADF is installed and used to enable the stream feeding mode of the optional document feeder. When the stream feeding mode is enabled, additional originals which are set in the document feeder tray within 5 seconds after the last original in a stack was fed will be fed and copied automatically. -
Page 27: Timer Settings
The sleep mode is a function to turn off the power to the fusing unit automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. -
Page 28: Preheat Mode Setting
We suggest you set the most appropriate time according to your usage pattern. This program is used to set the time that elapses before the copier enters the preheat mode after copying is completed. The interval can be set between 10 and 240 minutes in 1 minute increments. -
Page 29: Disabling Of Auto Paper Selection
Disabling of Auto Paper Selection This program is used to prevent automatic paper selection. When disabled, the copier will not automatically select a paper tray containing paper that matches the size of the original placed on the document glass or in the optional document feeder. -
Page 30: Disabling Deletion Of Job Programs
This program is used to enable or disable the optional duplex system. If a malfunction occurs within the duplex system of the copier, the system can be disabled until it is serviced. The rest of the copier in the meantime will remain operable. -
Page 31: Disabling Of Stapler
KEY OPERATOR PROGRAMS To disable the duplex system, press the check box of “DISABLING OF DUPLEX COPYING”... - Page 32 The sleep mode is used to turn off the power to the fusing unit automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. This mode lowers the user’s electricity bill, reduces waste of natural resources, and cuts down on environmental pollution.
-
Page 33: Total Count
Total Count This program is used to display the total counts, including counts of the copier, document feeder, duplex module, and stapler. An 11" x 17" or a 12" x 18" copy is counted as two copies. -
Page 34: Auto Color Calibration
The copier will print the test patch. After the test patch is printed, place it on the document glass of the copier with 5 white sheets of the same size on top of it and press the “EXECUTE” key again. - Page 35 These must be the same for automatic paper feeding to function. When the check mark is off, the settings for copier and printer can be different and will not be compared. When the settings are different, a selection from the printer driver will override any selection made at the copier.
- Page 36 KEY OPERATOR PROGRAMS Prohibit Bypass-Tray Selection If this program is set, the bypass tray will not be selected for a print job that specifies auto paper selection or during auto tray switching. Prohibit Auto Tray Switching This program prevents automatic switching between paper trays for print jobs.
-
Page 37: Key Operator Assistance Call
KEY OPERATOR ASSISTANCE CALL When the copier is in need of service or care not usually performed by general users, the copier will stop and one of the following messages listed below will appear. Message CHECK STAPLER POSITION OR STAPLE JAM. - Page 38 AR-C160 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. SHARP CORPORATION PRINTED IN JAPAN 2001E TINSE2099FCZZ...