1. Manuals
  2. Brands
  3. Schiller Grounds Care Manuals
  4. Lawn Mower
  5. RYAN 754874
  6. Operator's manual

Schiller Grounds Care RYAN 754874 Operator's Manual

Push-type scarifier - power rake
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PUSH-TYPE SCARIFIER - POWER RAKE
OPERATORS MANUAL 4173837
REN-O-THIN V BRIGGS & STRATTON
REN-O-THIN V HONDA
754874
W/ FIXED BLADE
754875
W/ FIXED BLADE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RYAN 754874 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Schiller Grounds Care RYAN 754874

Summary of Contents for Schiller Grounds Care RYAN 754874

  • Page 1 PUSH-TYPE SCARIFIER - POWER RAKE 754874 REN-O-THIN V BRIGGS & STRATTON W/ FIXED BLADE 754875 REN-O-THIN V HONDA W/ FIXED BLADE OPERATORS MANUAL 4173837...
  • Page 2 CALIFORNIA WARNING Proposition 65 Warning Diesel engine exhaust and some The engine exhaust from this product of its constituents are known to the contains chemicals known to the State State of California to cause cancer, of California to cause cancer, birth birth defects and other reproductive defects or other reproductive harm.

  • Page 3: Table Of Contents

    Your safe use of this Schiller Grounds Care, Inc. product is one of our prime design objectives. Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the manual thoroughly.

  • Page 4: Safety

    These words appear in this Grounds Care, Inc. Engineering Department. Any manual and on the safety labels attached to Schiller Schiller Grounds Care, Inc. product that is altered, Grounds Care, Inc. machines. For your safety and modified or changed in any manner not specifically the safety of others, read and follow the information authorized after original manufacture–including the...
  • Page 5 SAFETY REN-O-THIN PREPARING FOR SAFE OPERATION Operator preparation and training SITE PREPARATION AND CIRCUMSTANCES Read the Operation & Safety – Evaluate the terrain to determine how to safely Manual perform the job. Only use accessories and – If an operator or mechanic cannot read, it is the attachments approved by the manufacturer.
  • Page 6 SAFETY REN-O-THIN MACHINE PREPARATION STARTING – Check blade clutch operation. Adjust or have any problems repaired before using. – Start only according to instructions in this manual or on the machine. – Do not tamper with or defeat safety devices. Keep guards, shields and interlock safety devices –...
  • Page 7 SAFETY REN-O-THIN INTERRUPTING OPERATION MANUEVERING SAFELY Before leaving the operator's position: In General - Park on level ground. Operating on Slopes - Disengage the blades. USE EXTRA CARE WHEN WORKING ON SLOPES - Shut off the engine. BEFORE OPERATING ON A SLOPE, EVALUATE Disengage the blades and wait until the blades THE RISKS INVOLVED.
  • Page 8 SAFETY REN-O-THIN M AINTENANCE AND STORAGE SAFETY Keep the machine and fuel containers in a locked In general storage place to prevent tampering and to keep Maintain machine according to manufacturer's children from playing with them. schedule and instructions for maximum safety Blades and best results.

  • Page 9: Set-Up / Adjustments

    SET-UP INSTRUCTIONS / ADJUSTMENTS REN-O-THIN SET-UP INSTRUCTIONS 3. Roll the machine off the pallet onto a smooth, level WARNING surface. Banding is under tension and may snap back when 4. Check the oil level in the engine, add if necessary. cut.

  • Page 10: Maintenance

    MAINTENANCE REN-O-THIN When replacement parts are required, use genuine Schiller Grounds Care, Inc. parts or parts with equivalent characteristics, including type, strength and material. Failure to do so may result in product malfunction and possible injury to the operator and/or bystanders.

  • Page 11: Blade/ Spring Replacement

    BLADE / SPRING REPLACEMENT REN-O-THIN BLADE/SPRING REPLACEMENT Reel Remove/Replace 2. Install the bearing on the other end of the reel 1. Remove belt cover and belt. assembly, again with the lock collar to the inside and with flangettes on each side of the bearing. 2.
  • Page 12 FLAIL BLADE REPLACEMENT - 970962 REN-O-THIN FLAIL BLADE REELS NOTE: Work on only one of the six blade shaft assemblies at a time. 1. Remove reel assembly from machine. 2. Remove the cotter pin from one of the blade shafts and pull the shaft out. 3.
  • Page 13 970964 - SPRING TINE REPLACEMENT REN-O-THIN SPRING TINE REELS 1. Remove reel assembly from machine. 2. Remove the cotter pin from one of the spring tine shafts. Pull the shaft out. Replace the shaft if worn. 3. Install spring tines as the shaft is slid back into place. Secure with a new cotter pin. 4.

  • Page 14: Seeder Box

    SEEDER BOX - 970962 REN-O-THIN SEEDER ACCESSORY (970963) SEEDING RATES: INSTALLATION: (Use Figure 7 for reference) Use the seed chart on page 14 to give a starting point for seed gate control settings. Due to the 1. Install the latch assembly to the right front of the variable nature of seed* this chart should be used machine.

  • Page 15: Storage

    STORAGE REN-O-THIN STORAGE INSTRUCTIONS To put equipment into operation after an extended storage: To prevent possible explosion or ignition of vaporized fuel, do not store equipment with fuel 1. Fill fuel tank with clean fresh fuel. in tank or carburetor in enclosure with open flame (for example, a furnace or water heater pilot 2.

  • Page 16: Specifications / Seed Chart

    SPECIFICATIONS REN-O-THIN SPECIFICATIONS Chassis:...................... 12 gauge steel, formed and welded Reduction: ........................1.33:1 (engine to reel) Wheelbase:..................... 14 5/8" (371 mm) at level position Reel Speed: ............................1700 RPM Cutting Width: ..........................18" (457mm) Cutting Depth:...........................7/8" (22mm) Blade Adjustment:.........1" (25mm) above ground level to 7/8" (22mm) below ground level Weight (less reel): ........................

  • Page 17: Parts Section

    PARTS SECTION REN-O-THIN PARTS SECTION...

  • Page 18: Wheel And Chassis Group

    WHEEL AND CHASSIS GROUP REN-O-THIN FIGURE 1...
  • Page 19 WHEEL AND CHASSIS GROUP REN-O-THIN FIGURE 1 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4173842 S-ENGINE DECK (INCLUDES ITEMS 33 & 37-39) 4170043 WLDMT-AXLE 4170503.7 HANDLE-LIFT 38404-03 GRIP-CONTROL LEVER 4170034 WLDMT-CLEVIS 4169668 PLATE-LIFT 4170027 TRUNNION-.500 4170028 TRUNNION-5/8-11 4170079-02 SHAFT-2 GROOVE 2.50 LG 4170044 WLDMT-ADJ SCREW 4170045.7 WLDMT-LIFT HOUSING...

  • Page 20: Engine And Guard Group

    ENGINE AND GUARD GROUP REN-O-THIN FIGURE 2 HONDA MUFFLER GUARD 42 46 44 B & S MUFFLER GUARD...
  • Page 21 ENGINE AND GUARD GROUP REN-O-THIN FIGURE 2 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4166692 ENGINE-B&S 6.5HP 4163713 LABEL-RENOTHIN HOC 540354 ENGINE-HONDA GX160 ITEMS 40-46 USED ON B&S ENGINES ONLY 4164186.7 GUARD, MUFFLER (B&S) 4173842 S-ENGINE DECK 4160485.7 BRKT-HORIZONTAL (INCLUDES ITEMS 36-39) 4160484.7 BRKT-VERTICAL...

  • Page 22: Handle Group

    HANDLE GROUP REN-O-THIN FIGURE 3...
  • Page 23 HANDLE GROUP REN-O-THIN FIGURE 3 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4173835.7 HANDLE-RENOTHIN 4169665.7 BRKT-HANDLE LH 4169666.7 BRKT-HANDLE RH 4169638 CABLE-CONTROL 4169676 BRKT-HANDLE REST 64262-011 BLT-FLG HD 3/8-16 X 1 4173836.7 BAIL-CONTROL 64141-4 NUT-WLF 3/8-16 4168156 LOCK-HANDLE 4168728 SPACER-PIVOT 64262-012 BLT-FLG HD 3/8-16 X 1-1/4...

  • Page 24: Fixed Blade Reel

    FIXED BLADE REEL REN-O-THIN FIGURE 4...
  • Page 25 FIXED BLADE REEL REN-O-THIN FIGURE 4 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4169622 SHAFT-FIXED BLADE REEL 516905 SPACER .900 (23mm) 516898 BLADE, 1/8" (3.2mm) 516903 SPACER .500 64163-113 WSHR-.890X1.50X.090 64001-15 NUT-HEX JAM 7/8-14 820484 WASHER FLAT 1.17x1.75x.134 2 * NOT ILLUSTRATED...

  • Page 26: Flail Blade Reel

    FLAIL BLADE REEL (OPTIONAL KIT 970962) REN-O-THIN FIGURE 5...
  • Page 27 (OPTIONAL KIT 970962) FLAIL BLADE REEL REN-O-THIN FIGURE 5 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4170067.7 WLDMT-FLAIL SHAFT 516897 BLADE FLAIL 517155 SHAFT 517162 SPACER .328 (8mm) 517163 SPACER .891 (23mm) 64140-1 COTTER PIN-1/8X1 64163-67 WSHR-.516X1X12GA 64164-19 KEY-3/16X3/4 #9 WDRUFF * NOT ILLUSTRATED...

  • Page 28: Spring Tine Reel

    SPRING TINE REEL (OPTIONAL KIT 970964) REN-O-THIN FIGURE 6...
  • Page 29 (OPTIONAL KIT 970964) SPRING TINE REEL REN-O-THIN FIGURE 6 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4169624 ROD-SPRING MOUNTING 4169626 TINE-SPRING 4170068.7 WLDMT-SHAFT SPRING TINE 1 64140-1 COTTER PIN-1/8X1 64164-19 KEY-3/16X3/4 #9 WDRUFF * NOT ILLUSTRATED...

  • Page 30: Seed Box Assy (Optional)

    SEED BOX ASSEMBLY (OPTIONAL 970963) REN-O-THIN FIGURE 7 34 3...
  • Page 31 SEED BOX ASSEMBLY (OPTIONAL 970963) REN-O-THIN FIGURE 7 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4170999.2 PLATE-MAIN BODY CLOSE 1 4171000.7 SEED GATE FLAT 2183063-01 SPACER 32MM LONG 38404-03 GRIP-CONTROL LEVER 38524 KNOB-4 PRONG 3/8-16 4165854 WASHER-UHMW PE 4166457 CLEVIS-CABLE 4168826 LABEL-RYAN OVAL 9"...
  • Page 32 SCHILLER GROUNDS CARE, INC. ONE BOB-CAT LANE P.O. BOX 469 JOHNSON CREEK, WI 53038 920-699-2000 www.schillergc.com ©Schiller Grounds Care, Inc. 2010...

This manual is also suitable for:

Ryan 754875

Table of Contents