TYAN S8050 Manual
  1. Manuals
  2. Brands
  3. TYAN Manuals
  4. Motherboard
  5. S8050
  6. Manual

TYAN S8050 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

S8050

Version 1.0c
Copyright
Copyright © 2022 MiTAC International Corporation. All rights reserved. No part of
this manual may be reproduced or translated without prior written consent from
MiTAC International Corporation.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
®
TYAN
is a trademark of MiTAC International Corporation.
®
®
AMD
is a trademark of AMD
Corporation.
AMI, AMI BIOS are trademarks of AMI Technologies.
Microsoft
®
, Windows
®
are trademarks of Microsoft Corporation.
®
Winbond
is a trademark of Winbond Electronics Corporation.
Notice
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to printing.
MiTAC assumes no liability whatsoever, and disclaims any express or implied
®
warranty, relating to sale and/or use of TYAN
products including liability or
warranties relating to fitness for a particular purpose or merchantability. MiTAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MiTAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
1
http://www.tyan.com

Advertisement

Table of Contents
loading

Related Manuals for TYAN S8050

Summary of Contents for TYAN S8050

  • Page 1: S8050

    Corporation and has been reviewed for accuracy and reliability prior to printing. MiTAC assumes no liability whatsoever, and disclaims any express or implied ® warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or merchantability. MiTAC retains the right to make changes to product descriptions and/or specifications at any time, without notice.

  • Page 2: Table Of Contents

    Contents S8050 ......................1   Before you begin… ..................3   Chapter 1: Instruction ................4   1.1 Congratulations ................. 4   1.2 Hardware Specifications ..............4   1.3 Software Specifications ..............8   Chapter 2: Board Installation ..............9  ...

  • Page 3: Before You Begin

    SATA Cable x 2 M.2 Latch x 2 Rear IO shielding x 1 1 x S8050 Quick Installation Guide IMPORTANT NOTE: Sales samples may not come with any of the accessories listed above. If you have ordered a sales sample and you are missing any of the above items, please contact your sales representative to help order accessories.

  • Page 4: Chapter 1: Instruction

    32 and 64-bit computing, high-bandwidth memory design, and lightning- fast PCI-E bus implementation. The S8050 not only empowers you in today’s demanding IT environment but also offers a smooth path for future application upgradeability. All of these rich feature sets provide the S8050 with the power and flexibility to meet demanding requirements for today’s IT environments.
  • Page 5 Hardware Monitor / FAN speed control automatic / BIOS Boot from USB device/PXE via LAN/Storage / Console Redirection / SMBIOS 3.0/PnP/Wake on LAN / ACPI sleeping states S0, S5 Form Factor Physical Dimension Board Dimension 12” x 10.5” (305 x 267mm) http://www.tyan.com...
  • Page 6 90%, non-condensing at 35° C Humidity RoHS 6/6 Compliant RoHS OS supported list Please refer to our AVL support lists. Operating System Motherboard (1) S8050 Motherboard Manual (1) Quick Installation Guide Package Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables...
  • Page 7 SATA (2) Mini-SAS HD (SFF-8643) connectors / (4) 7-pin SATA connectors Power (2) 2x4 Power input connectors / (1) 2x12 Power input connectors Others (1) ID button TPM Support Please refer to our TPM supported list. TPM (Optional) Interface http://www.tyan.com...

  • Page 8: Software Specifications

    Contains I/O Shield (1) I/O Shield Cable SATA (2) SATA signal cables   1.3 Software Specifications For the latest AST2600 User’s Guide and OS (operation system) support, please visit the Tyan’s Web site at http://www.tyan.com for the latest information http://www.tyan.com...

  • Page 9: Chapter 2: Board Installation

    Caution! To avoid damaging the motherboard and associated components, do not use torque force greater than 5~7kgf/cm (4.35~6.09 lb/in) on each mounting screw for motherboard installation. Do not apply power to the board if it has been damaged. http://www.tyan.com...

  • Page 10: Board Image

    2.1 Board Image S8050GM2NE-2T This picture is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above picture. http://www.tyan.com...

  • Page 11: Block Diagram

    2.2 Block Diagram S8050 Block Diagram http://www.tyan.com...

  • Page 12: Motherboard Mechanical Drawing

    2.3 Motherboard Mechanical Drawing http://www.tyan.com...

  • Page 13: Board Parts, Jumpers And Connectors

    The board you receive may not look exactly like the above diagram. The DIMM slot numbers shown above can be used as a reference when reviewing the DIMM population guidelines shown later in the manual. For the latest board revision, please visit our web site at http://www.tyan.com. http://www.tyan.com...
  • Page 14 26. 4-pin Fan Connector (SYS_FAN_2) 2. Front Fan Header(FAN_HD1) 27. M.2 Connector (CN1) PCIE only 3. COM2 Port Header(COM2) 28. MCIOx4 SATA/NVME (CN10) 4. TYAN Module Header(J62) 29. 4-pin Fan Connector (SYS_FAN_1) 5. TYPE A USB3.2 Gen1 30. 7p SATA Connector (J15) Header(TYPEA_USB1) 6.
  • Page 15 PROCHOT LED PWROK LED BMC heartbeat LED BMC ALERT LED CPU RESET LED VIII SYS_PWROK LED SATA & M.2 LED PSU_ALERT LED PWR_GOOD LED Jumper Legend OPEN - Jumper OFF Without jumper cover CLOSED - Jumper ON With jumper cover http://www.tyan.com...
  • Page 16 FPIO_2: Front Panel Connector Signal Signal PWRLED+ VDD_33_DUAL IDLED+ PWRLED- IDLED- HDDLED+ SYS_FAULT1- HDDLED- SYS_FAULT2- PWR_SW# LAN1LED+ LAN1LED- RESET_SW# SMBDATA SMBCLK IDLED_SW# INTRUSION# LAN2LED+ NMI_SW# LAN2LED- PSMI_HD1: PSMI Header Signal SMB_CLK SMB_DAT PSU_SMBALERT_N V3.3 IPMB_HD1: 4-pin IPMB Connector Signal IPMB_DAT IPMB_CLK VCC3_AUX http://www.tyan.com...
  • Page 17 J62: TYAN Module Header Signal Signal VDD_33_DUAL ESPI_CS1 RESET# ALERT FAN_HD1: Front Fan Connector (Reserved for Barebone) Signal Signal TACH1 TACH6 TACH2 TACH7 TACH3 TACH8 TACH4 TACH9 TACH5 TACH10 PWM3 PWM2 TACH11 TACH12 PWM4 TACH13 TACH15 TACH14 TACH16 PWM5 PWM7 PWM0 USB3_FPIO1: USB3.2 Gen1 Header...
  • Page 18 COM2: COM Port Header Signal Signal COM2_DCD COM2_DSR COM2_RXD COM2_RTS COM2_TXD COM2_CTS COM2_DTR COM2_NRI HDR_1/2: HDD BP Smbus Header Signal Signal VCC3_AUX HP0_SCK HP0_SDA CPU01_SMBALERT_N_C TYPEA_USB1: Vertical Type-A USB3.2 Gen1 Connector Signal Signal USB3_N3_RX_TYPEA VCC5 USB3_P3_RX_TYPEA USB2_N8_TYPE_A_R USB2_P8_TYPE_A_R USB3_N3_TX_TYPEA USB3_P3_TX_TYPEA http://www.tyan.com...
  • Page 19 Signal Signal PWR_BTN1 RST_BTN1: COLD Reset Button Signal Signal FP_RST_BTN_N BIOS_DBG1: BIOS Debug Header Signal Signal SPI_CS# VDD_33_DUAL SPI_DO SPI_HOLD# SPI_WP# SPI_CLK SPI_DI J66: Intrusion Header Signal SCM_CHASSIS_INTR_L J1: HDT Header Signal Signal P1V8_AUX TRST_N PEROK RESET_N DBREQ_N P1V8_AUX http://www.tyan.com...
  • Page 20 CN1/CN2: M.2 Connector Signal Signal VCC3 VCC3 VCC3_AUX M2_LED_N VCC3 VCC3 VCC3 VCC3 PCH_PE1_M2_1_RX_N PCH_PE1_M2_1_RX_P PCH_PE1_M2_1_TX_N PCH_PE1_M2_1_TX_P M2_SMB_CLK_R PCH_PE0_M2_0_RX_N M2_SMB_DAT_R PCH_PE0_M2_0_RX_P PCH_PE0_M2_0_TX_N M2_PERST_N_R PCH_PE0_M2_0_TX_P M2_2_PEWAKE_N CLK_100M_M2_DN CLK_100M_M2_DP PE_M.2_DETECT_N VCC3 VCC3 VCC3 http://www.tyan.com...
  • Page 21 A27 B27 CPU0_PE4_HDD0_SDA1 A28 B28 GND CLK_100M_DB2000_CPU0_N A29 B29 RST_NVME1_CPU0_PERST_N VME2_DP CLK_100M_DB2000_CPU0_N A30 B30 FM_CPU0_PE4_PRSTNB_N VME2_DN A31 B31 GND CPU0_PE4_RX_DN<1> A32 B32 CPU0_PE4_TX_DN<1> CPU0_PE4_RX_DP<1> A33 B33 CPU0_PE4_TX_DP<1> A34 B34 GND CPU0_PE4_RX_DN<0> A35 B35 CPU0_PE4_TX_DN<0> CPU0_PE4_RX_DP<0> A36 B36 CPU0_PE4_TX_DP<0> A37 B37 GND http://www.tyan.com...
  • Page 22 J4: NCSI SEL Connector Signal Signal NCSI_X710_I210_EN Pin1-2 closed: NCSI to OCP (Default) Pin2-3 closed: NCSI to X710 J33: reset SYS/BMC SEL Connector Signal Signal COLD_RST_BTN_L FP_RST_BTN_JP_L FP_BMC_RST_BTN_N Pin1-2 closed: SYS RESET (Default) Pin2-3 closed: BMC RESET J75: Clear CMOS Jumper http://www.tyan.com...

  • Page 23: Led Definitions

    Signal Signal BMC_TXD1 TXD_OUT BMC_RXD1 RXD_OUT FTDI_UART_RXD FTDI_UART_TXD Pin1-2 closed: Normal Mode (Default) Pin2-3 closed: Debug Mode J15/J16/J18/J19: 7-pin SATA 3.0 Connector Name TYPE SATA TX DP SATA TX DN SATA RX DN SATA RX DP 2.5 LED Definitions http://www.tyan.com...
  • Page 24 1. D39 SATA & M.2 LED Signal http://www.tyan.com...
  • Page 25 CPU Reset Not Send Out Signal VDD_33_DUAL BMC_P0_PROCHOT_N 5. D26 PROCHOT LED State Description Normal SYSTEM PROCHOT OR BMC NOT ready Signal VDD_33_DUAL PSMI_PSU_ALERT_LED_L PSU_ALERT 6. D31 State Description Normal PSU_ALERT Signal VDD_33_DUAL SYS_PWROK 7. D32 SCM_SYS_PWROK- State Description http://www.tyan.com...

  • Page 26: Installing The Processor And Heatsink

    Green System Power OK Signal VDD_33_DUAL BMC_HB_LED_L BMC heartbead 8. D1_2 State Description BMC Not Ready Green BMC Ready Signal VDD_33_DUAL BMC_HW_FAULT_L 9. D18 BMC ALERT LED State Description Normal Orange BMC Alert 2.6 Installing the Processor and Heatsink http://www.tyan.com...
  • Page 27 The types of processors supported by the S8050 are listed in the 1.2 Hardware Specifications section on page 4. Check our website at http://www.tyan.com ® the latest list of validated AMD processors for this specific motherboard. NOTE: MiTAC is not liable for damage as a result of operating an unsupported configuration.
  • Page 28 Carefully close the rail frame with the installed package. Then push both edges of the rail frame firmly until it locks in place. Close the force frame. Then use a T20 Torx screwdriver to tighten the screw to secure the force frame. Heat sink Installation http://www.tyan.com...
  • Page 29 The following diagram illustrates how to install the heatsink on the AMD Socket: 1. Align and install the CPU heatsink onto the top of the CPU socket. Use a T20 Torx screwdriver to tighten the heatsink screws. Connect the heatsink power cable to the mainboard connector. http://www.tyan.com...

  • Page 30: Thermal Interface Material

    CPU lid (applying too much will actually reduce the cooling). NOTE: Always check with the manufacturer of the heat sink & processor to ensure that the thermal interface material is compatible with the processor and meets the manufacturer’s warranty requirements. http://www.tyan.com...

  • Page 31: Tips On Installing Motherboard In Chassis

    Be especially careful to look for extra stand-offs. If there are any stand-offs present that are not aligned with a mounting hole on the motherboard, it will likely short components on the back of the motherboard when installed. This will cause malfunction and/or damage to your motherboard. http://www.tyan.com...
  • Page 32 Some chassis include plastic studs instead of metal. Although the plastic studs are usable, MiTAC recommends using metal studs with screws that will fasten the motherboard more securely in place. Below is a chart detailing what the most common motherboard studs look like and how they should be installed. http://www.tyan.com...

  • Page 33: Installing The Memory

    2.9 Installing the Memory Before installing memory, ensure that the memory you have is compatible with the motherboard and processor. Check the TYAN Web site at http://www.tyan.com details of the type of memory recommended for your motherboard. http://www.tyan.com...
  • Page 34 When x = 4 DIMM Ranks = 8 When x = 8 DIMM Ranks = 16 DIMM SLOT Silk screen DIMM SLOT Silk screen P0_UMC3_CH_A0 P0_CHA_DIM0 P0_UMC9_CH_G0 P0_CHG_DIM0 P0_UMC4_CH_B0 P0_CHB_DIM0 P0_UMC10_CH_H0 P0_CHH_DIM0 P0_UMC0_CH_C0 P0_CHC_DIM0 P0_UMC6_CH_I0 P0_CHI_DIM0 P0_UMC1_CH_E0 P0_CHE_DIM0 P0_UMC7_CH_K0 P0_CHK_DIM0 http://www.tyan.com...
  • Page 35 Recommended Memory Population Table Quantity of memory installed CPU Installed P0_CHA_DIM0 √ √ √ √ √ P0_CHB_DIM0 √ √ √ √ √ P0_CHC_DIM0 P0_CHE_DIM0 √ √ √ √ √ P0_CHG_DIM0 √ √ P0_CHH_DIM0 √ √ √ P0_CHI_DIM0 P0_CHK_DIM0 √ http://www.tyan.com...
  • Page 36 Memory Installation Procedure Follow these instructions to install memory modules into the S8050. Unlock a DIMM socket by Press the retaining clip outwardly in the following illustration. Align the memory module with the socket，such that the DIMM NOTCH match the KEY SLOT on the socket.

  • Page 37: Installing Add-In Cards

    Doing so allows air to circulate within the chassis more easily, thus improving cooling for all installed devices. NOTE: You must always unplug the power connector from the motherboard before performing system hardware changes to avoid damaging the board or expansion device. http://www.tyan.com...

  • Page 38: Connecting External Devices

    1. For S8050GM4NE-2T Sku: RJ45 (10GbE) LAN1/LAN2 is from Intel X710-AT2. RJ45 (1GbE) LAN3/LAN4 are from Intel I210-AT chipset. LAN5 is from RTL8211F 2. For S8050GM2NE Sku: RJ45 (1GbE) LAN1/ LAN2/ is from Intel I210-AT chipset. LAN3 is from RTL8211F http://www.tyan.com...

  • Page 39: Installing The Power Supply

    Solid Yellow 10Gbps Solid Yellow Active Blinking Yellow 2.12 Installing the Power Supply There are Three (3) power connectors on your S8050 motherboard. The S8050 supports EPS 12V power supply. PWR1: ATX 24-pin Main Power Connector Signal Signal +3.3V_1 +3.3V_4 +3.3V_2...

  • Page 40: Finishing Up

    In the rare circumstance that you have experienced difficulty, you can find help by asking your vendor for assistance. If they are not available for assistance, please find setup information and documentation online at our website or by calling your vendor’s support line. http://www.tyan.com...

  • Page 41: Chapter 3: Bios Setup

    Exit current menu <F1> General help <F2> Previous values <F3> Load the Optimal default configuration values of the menu <F4> Save and exit <K> Scroll help area upwards <M> Scroll help area downwards <PgUp> / <PgDn> Move cursor to next/previous page http://www.tyan.com...
  • Page 42 BIOS menus are continually changing due to continual BIOS updates over the product lifespan of the motherboard. The BIOS menus provided are current as of the date when this manual was written. Please visit TYAN’s website at http://www.tyan.com for information on BIOS updates available for this specific motherboard.

  • Page 43: Main Menu

    It displays BIOS related information. Product Name It displays Product information. BIOS Version It displays BIOS version information Build Date and Time It displays the time when built Memory Information It displays the total memory size. Memory Frequency It displays Memory frequency http://www.tyan.com...
  • Page 44 System Date Set the Date. Use Tab to switch between Date elements. Default Ranges: Year: 2005-2099 Months: 1-12 Days: dependent on month System Time Adjust the system clock. HH (24 hours format): MM (Minutes): SS (Seconds) Access Level Administrator http://www.tyan.com...

  • Page 45: Advanced Menu

    Network Stack Configuration Network Stack Settings S5 RTC Wake Settings Enable system to wake from S5 using RTC alarm Serial Port Console Redirection Serial Port Console Redirection PCIe Device Configuration Onboard PCIE Slot Configuration USB Configuration USB Configuration Parameters http://www.tyan.com...
  • Page 46 VLAN Configuration(MAC: 8ACE8EEDBEF9) MAC: 8ACE8EEDBEF9-IPv4 Network Configuration Configure IPv4 network parameters.(MAC: 8ACE8EEDBEF9) MAC: 8ACE8EEDBEF9-IPv6 Network Configuration Configure IPv6 network parameters.(MAC: 8ACE8EEDBEF9) Intel(R) I210 Gigabit Network Connection Configure Gigabit Ethernet device parameters. VLAN Configuration (MAC :A0423F50572F) VLAN Configuration (MAC :A0423F50572F) http://www.tyan.com...
  • Page 47 Intel® I210 Gigabit Network Connection Configure Gigabit Ethernet device parameters. VLAN Configuration (MAC:A0423F505730) VLAN Configuration (MAC:A0423F505730) MAC:A0423F505730-IPv4 Network Configuration Configure network parameters(MAC:A0423F505730) MAC: A0423F505730-IPv6 Network Configuration Configure network parameters(MAC:A0423F505730) 3.3.1 Network Stack Configuration Network Stack Enable/Disable UEFI Network Stack Disabled / Enabled http://www.tyan.com...
  • Page 48 Wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. http://www.tyan.com...
  • Page 49 Wake system from S5 Enable or disable system wake on alarm event. Select Fixed time, system will wake on the hr::min::sec specified. Select dynamic time, system will wake on the current time+ increase minute(s) Disabled / Fixed Time / Dynamic Time http://www.tyan.com...
  • Page 50 Serial Port for Out-Of-Band Management/Windows Emergency Services (EMS) Console Redirection Console redirection enable or disable. Disabled / Enabled Console Redirection Settings The settings specify how the host computer (which the user is using) will exchange data. Both computers should have the same or compatible settings. http://www.tyan.com...
  • Page 51 Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 9600 / 19200 / 38400 / 57600 / 115200 Data Bits 8 / 7 http://www.tyan.com...
  • Page 52 With this mode enabled only text will be sent. This is to capture Terminal data. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400 http://www.tyan.com...
  • Page 53 1’s in the data bits is odd. Mark: parity bit is always 1. Space: parity bit is always 0. Mark and Space parity do not allow for error detection. None / Even / Odd / Mark / Space http://www.tyan.com...
  • Page 54 With this mode enabled only text will be sent. This is to capture Terminal data. Disabled / Enabled Resolution 100x31 Enable or disable extended terminal resolution. Disabled / Enabled Putty KeyPad Select FunctionKey and KeyPad on Putty. VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400 http://www.tyan.com...
  • Page 55 Bootloader is selected, then Legacy Console Redirection is disabled before booting to legacy OS, when Always Enable is selected, then Legacy Console Redirection is enabled for Legacy OS. Default setting for this option is set to Always Enable. Always Enable / BootLoader http://www.tyan.com...
  • Page 56 VT-UTF8 / VT100 / VT100+ / ANSI Bits per Second Select serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds. 9600 / 19200 / 57600 / 115200 http://www.tyan.com...
  • Page 57 Data Bits EMS / Parity EMS / Stop Bits EMS Read only. 3.3.4 PCIe Device Configuration Option ROM Dispatch Policy Option ROM Dispatch Policy settings. PCIe Slot Bifurcation PCIe Slot Bifurcation settings. PCIe Slot Speed PCIe Slot Speed settings. http://www.tyan.com...
  • Page 58 Enable or Disable LAN1 Option ROM. Enabled / Disabled PCIE#2 Option ROM Enable or Disable Option ROM execution for selected Slot. Enabled / Disabled PCIE#3 Option ROM Enable or Disable Option ROM execution for selected Slot. Enabled / Disabled http://www.tyan.com...
  • Page 59 Enable or Disable Option ROM execution for selected Slot. Enabled / Disabled 3.3.4.2 PCIe Slot Bifurcation PESLOT1 Selects PCIE port Bifurcation for PCIE#1/PCIE#2 slots. X16 / x8x8 / x4x4x4x4 PESLOT2 Selects PCIE port Bifurcation for PCIE#3/PCIE#4 slots. X16 / x8x8 / x4x4x4x4 http://www.tyan.com...
  • Page 60 NVME0/1/2/3 Selects PCIE port Bifurcation for PCIE#9/PCIE#10 X16 / x8x8 / x4x4x4x4 3.3.4.3 PCIe Slot Speed PESLOT1 Maximum Link Speed for PCIE#1/PCIE#2 slots. Auto / GEN1(2.5 GT/s) / GEN2(5 GT/s) / GEN3(8 GT/s) / GEN4(16 GT/s) / GEN5 (32GT/s) http://www.tyan.com...
  • Page 61 Auto / GEN1(2.5 GT/s) / GEN2(5 GT/s) / GEN3(8 GT/s) / GEN4(16 GT/s) / GEN5 (32GT/s) NVME0/1/2/3 Maximum Link Speed for PCIE#7/PCIE#8 slots. Auto / GEN1(2.5 GT/s) / GEN2(5 GT/s) / GEN3(8 GT/s) / GEN4(16 GT/s) / GEN5 (32GT/s) http://www.tyan.com...
  • Page 62 USB Mass Storage Driver Support Enable/Disable USB Mass Storage Driver Support. Disabled / Enabled Port 60/64 Emulation Enable I/O port 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USB aware OSes. Disabled / Enabled http://www.tyan.com...
  • Page 63 Maximum time the device will take before it properly reports itself to the Host Controller. AUTO uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor. Auto / Manual http://www.tyan.com...
  • Page 64 Disabled / Enabled LAN (X710) LAN Enable/Disable control function. Disabled / Enabled LAN (I210-1) LAN Enable/Disable control function. Disabled / Enabled LAN (I210-2) LAN Enable/Disable control function. Disabled / Enabled Primary Display Select active Video type. Onboard / External http://www.tyan.com...
  • Page 65 Disabled / Enabled Clock Spread Spectrum Enable/Disable Clock Spread Spectrum Disabled / Enabled 3.3.7 Super IO Configuration Serial Port 1 Configuration Set Parameters of serial Port 1 (COMA) Serial Port 2 Configuration Set Parameters of serial Port 2 (COMB) http://www.tyan.com...
  • Page 66 Serial Port has set to Enabled, the following items will be appear. Change Settings Allows the user to change the device resource settings. New settings will be reflected on this setup page after system restarts. Auto / IO=3F8h; IRQ=4; / IO=2F8h, IRQ=4, / IO=3F8h; IRQ=4, / IO=2E8h, IRQ=4, http://www.tyan.com...
  • Page 67 Serial Port has set to Enabled, the following items will be appear. Change Settings Allows the user to change the device resource settings. New settings will be reflected on this setup page after system restarts. Auto / IO=3F8h; IRQ=3; / IO=2F8h, IRQ=3, / IO=3E8h; IRQ=3, / IO=2E8h, IRQ=3, http://www.tyan.com...
  • Page 68 PWM Minimal Duty Cycle PWM Minimal Duty Cycle BMC Alert Beep Enable/Disable BMC Alert Beep. On / Off PMBus support PMBus Support Disabled / Enabled NOTE: When PMBus support was set to [Enabled] Number of PSU Item will appear. http://www.tyan.com...
  • Page 69 1 / 2 3.3.8.1 Sensor Data Register Monitoring When you enter the Sensor Data Register Monitoring submenu, you will see the following dialog window pop out. Please wait 8~10 seconds. NOTE 1: SDR can not be modified. Read only. http://www.tyan.com...
  • Page 70 http://www.tyan.com...
  • Page 71 Space(Only if System supports 64 bit PCI Decoding). Enabled / Disabled SR-IOV Support If system has SR-IOV capable PCIe devices, this option Enables or Disables Single Root IO virtualization Support Enabled / Disabled PCI Express Settings Change PCI Express Devices Settings http://www.tyan.com...
  • Page 72 3.3.9.1 PCI Express Subsystem Maximum Payload Set Maximum Payload of PCI Express Device or allow System BIOS to select the value. Auto / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048 Bytes / 4096 Bytes http://www.tyan.com...
  • Page 73 3.3.10 NVMe Configuration http://www.tyan.com...
  • Page 74 3.3.11 SATA Configuration http://www.tyan.com...
  • Page 75 Enables or disables BIOS support for security device. O.S. will not show Security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. Enabled / Disabled Disable Block sid Override to allow SID authentication in TCG Storage device. Enabled / Disabled http://www.tyan.com...
  • Page 76 Controls the execution of UEFI and legacy PXE OpROM UEFI / legacy Video Controls the execution of UEFI and legacy Video OpROM UEFI / legacy Other PCI devices Determines OpRom execution policy for devices other than network, storage, or video UEFI / legacy http://www.tyan.com...
  • Page 77 3.3.14 Redfish Host Interface Settings Redfish Enable/Disable AMI Redfish. Disabled / Enabled http://www.tyan.com...
  • Page 78 3.3.15 Tls Auth Configuration Server CA Configuration Press <Enter> to configure Server CA. http://www.tyan.com...
  • Page 79 3.3.15.1 Tls Auth Configuration Enroll Cert Press <Enter> to enroll cert. Delete Cert Press <Enter> to delete cert. http://www.tyan.com...
  • Page 80 3.3.15.1.1 Enroll Cert Configuration Enroll Cert Using File Enroll Cert Using File Cert GUID Input digit character in 11111111-2222-3333-4444-1234567890ab format. Commit Changes and Exit Commit Changes and Exit Discard Changes and Exit Discard Changes and Exit http://www.tyan.com...
  • Page 81 3.3.15.1.2 Delete Cert Configuration FEXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXX GUID for CERT Disabled / Enabled http://www.tyan.com...
  • Page 82 3.3.16 ISCSI Initiator Configuration Attempt Priority Change the priority using +/- keys. Use arrow keys to select the attempt then press +/- to move the attempt up/down in the attempt order list. Host iSCSI Configuration Host iSCSI Configuration settings http://www.tyan.com...
  • Page 83 3.3.16.1 Attempt Priority Attempt Priority Change the priority using +/- keys. Use arrow keys to select the attempt then press +/- to move the attempt up/down in the attempt order list. Host Attempt / Redfish Attempt Commit Changes and Exit http://www.tyan.com...
  • Page 84 Save changes and reboot. iSCSI Initiator Name The worldwide unique name of iSCSI Initiator. Only IQN format is accepted. Range is from 4 to 223. Add an Attempt Add one or more attempts Attempt 1 Attempt 2 Attempt 3 http://www.tyan.com...
  • Page 85 Delete Attempts Delete one or more attempts Change Attempt Order Change attempt sequence 3.3.16.3 Add an Attempt Read only. http://www.tyan.com...
  • Page 86 IPv4 / IPv6 / Autoconfigure Connection Retry Count The minimum value is 0 and the maximum is 16. 0 means no retry. Connection Establishing Timeout The timeout value in milliseconds. The minimum value is 100 milliseconds and the maximum is 20 seconds. http://www.tyan.com...
  • Page 87 Target Port Target Port. Boot LUN Hexadecimal representation of the LU number. Examples are: 4752-3A4F-6b7e- 3F99, 6734-9-156f-127, 4186-9. Authentication Type Authentication method: CHAP, Kerberos, or None. CHAP / None Save Changes Must reboot system manually for changes to take place. http://www.tyan.com...
  • Page 88 IPv4 / IPv6 / Autoconfigure Connection Retry Count The minimum value is 0 and the maximum is 16. 0 means no retry. Connection Establishing Timeout The timeout value in milliseconds. The minimum value is 100 milliseconds and the maximum is 20 seconds. http://www.tyan.com...
  • Page 89 Target Port Target Port. Boot LUN Hexadecimal representation of the LU number. Examples are: 4752-3A4F-6b7e- 3F99, 6734-9-156f-127, 4186-9. Authentication Type Authentication method: CHAP, Kerberos, or None. CHAP / None Save Changes Must reboot system manually for changes to take place. http://www.tyan.com...
  • Page 90 Disabled / Enabled Attempt 3 MAC: 36:02:0B:83:D7:63, PFA: Bus 35 / Dev 0 / Func 3, iSCSI mode: Disabled, IP version: IPv4. Disabled / Enabled Commit Changes and Exit Commit Changes and Exit. Discard Changes and Exit Discard Changes and Exit. http://www.tyan.com...
  • Page 91 Change the order of Attempts using +/- keys. Use arrow keys to select the attempt then press +/- to move the attempt up/down in the attempt order list. Attempt 1 / Attempt 2 / Attempt 3 Commit Changes and Exit Commit Changes and Exit. Discard Changes and Exit Discard Changes and Exit. http://www.tyan.com...
  • Page 92 3.3.17 VLAN Configuration Enter Configuration Menu Press ENTER to enter configuration menu for VLAN configuration. http://www.tyan.com...
  • Page 93 3.3.17.1 Enter Configuration VLAN ID VLAN ID of new VLAN or existing VLAN, valid value is 0~4094 Priority 802.1Q Priority, valid value is 0~7 Add VLAN Create a new VLAN or update existing VLAN Remove VLAN Remove selected VLANs http://www.tyan.com...
  • Page 94 Disabled / Enabled Local IP Address Enter IP address in dotted-decimal notation. Example: 162.168.10.12 Local NetMask Enter Netmask in dotted-decimal notation. Example:255.255.255.0 Local Gateway Enter Gateway in dotted-decimal notation. Example:192.168.10.1 Local DNS Servers Enter DNS Servers in dotted-decimal notation. Example:192.168.10.8 192.168.10.9 http://www.tyan.com...
  • Page 95 Save Changes and Exit Save Changes and Exit 3.3.19 MAC: 92044C4359EF-IPv6 Network Menu Enter Configuration Menu Press ENTER to enter configuration menu for VLAN configuration. http://www.tyan.com...
  • Page 96 Duplicate Address Detection on a tentative address. A value of zero indicates that duplicate address detection is not performed. Policy Automatic or manual Automatic / manual Save Changes and Exit Save changes for interface ID, DAD transmit count, policy, and data in advanced configuration. http://www.tyan.com...

  • Page 97: Cpu Configuration

    3.4 CPU Configuration CPU Configuration CPU Configuration Parameters http://www.tyan.com...
  • Page 98 3.4.1 CPU Configuration Submenu SVM Mode Enable/disable CPU Virtualization Enabled / Disabled SMEE Control secure memory encryption enable Enabling both SMEE and SME-Mk is not supported. Results in #GP Enabled / Disabled CPU0 Information View Information related to CPU 0 http://www.tyan.com...
  • Page 99 3.3.4.1.1 CPU0 Information http://www.tyan.com...

  • Page 100: Chipset Menu

    3.5 Chipset Menu PCIe Compliance Mode PCIe Link Compliance Mode Settings Enabled Disabled North Bridge North Bridge Parameters AMD CBS AMD CBS Setup Page AMD PBS AMD PBS Setup Page http://www.tyan.com...
  • Page 101 3.5.1 North Bridge Configuration North Bridge Configuration Memory Information Total Memory： xxxxx MB CPU 0 Information View Memory Information related to CPU 0 http://www.tyan.com...
  • Page 102 3.5.1.1 CPU 0 Information http://www.tyan.com...
  • Page 103 3.5.2 AMD CBS Menu CPU Common Options CPU Common Parameters DF Common Options DF Common Parameters UMC Common Options UMC Common Parameters NBIO Common Options NBIO Common Parameters FCH Common Options FCH Common Parameters Soc Miscellaneous Control Soc Miscellaneous Control parameters http://www.tyan.com...
  • Page 104 Enable/disable PFEH, cloak individual banks, and mask deferred error interrupts from each bank. Enabled / Disabled / Auto Core Performance Boost Disable CPB Disabled / Auto Global C-state Control Controls IO based C-state generation and DF C-states. Disabled / Enabled / Auto http://www.tyan.com...
  • Page 105 When this option is enabled, uncorrected errors detected by the PSP FW or SMU FW that should cause a cold reset, will hang and not reset the system. Disabled / Enabled / Auto Log Transparent Errors Log transparent errors in MCA in addition to debug registers. Auto / Disabled / Enabled http://www.tyan.com...
  • Page 106 FIVE (5 + 0) / SIX (6 + 0) / SEVEN (7 + 0) SMT Control Can be used to disable symmetric multithreading. To re-enable SMT, a POWER CYCLE is needed after selecting the ‘Auto’option. Disabled / Enabled / Auto http://www.tyan.com...
  • Page 107 3.5.2.1.2 Prefetcher Submenu L1 Stream HW Prefetcher Option to Enable | Disable L1 Stream HW Prefetcher Disabled / Enabled / Auto L2 Stream HW Prefetcher Option to Enable | Disable L2 Stream HW Prefetcher Disabled / Enabled / Auto http://www.tyan.com...
  • Page 108 3.5.2.2 DF Common Options Submenu PSP error injection support Enable EINJ support False / True http://www.tyan.com...
  • Page 109 Specifies the number of desired NUMA nodes per socket. Zero will attempt to interleave the two sockets together. NPS0 / NPS1 / NPS2 / NPS4 Memory interleaving Allows for disabling memory interleaving. Note that NUMA nodes per socket will be honored regardless of this setting. Disabled / Auto http://www.tyan.com...
  • Page 110 ACPI Submenu ACPI SRAT L3 Cache As NUMA Domain Enabled: Each CCX in the system will be declared as a separate NUMA domain. Disabled: Memory Addressing \ NUMA nodes per socket will be declared. Disabled / Enabled / Auto http://www.tyan.com...
  • Page 111 3.5.3 UMC Common Options Submenu DDR Addressing Options DDR addressing parameters DDR Timing Configuration DDT Timing parameters DDR RAS DDR RAS parameters DDR Security DDR Security parameters http://www.tyan.com...
  • Page 112 3.5.3.1 DDR Addressing Options Submenu Chipselect Interleaving Interleave memory blocks across the DRAM chip selects for node 0. Disabled / Auto BankSwapMode BankSwapMode value: 0=Disabled, 1= SwapCPU Disabled / Auto http://www.tyan.com...
  • Page 113 Auto / Enabled Memory Target Speed Specifies the memory target speed in MT/s. The valid input is 3200, 3600, 4000,4400,4800,5200, 5600. Value in decimal. Auto / DDR3200 / DDR3600 / DDR4000 / DDR4400 / DDR4800 / DDR5200 / DDR5600 http://www.tyan.com...
  • Page 114 Enable or Disable DRAM Run Time Post Package Repair. Disabled / Enabled RCD Parity Enable RCD command and address parity. Auto / Disabled / Enabled Disable Memory Error Injection 0=Enable. 1=Disable. Specifies UMC error injection configuration writes are disabled. True:: CH:: MiscCfg[DisErrInj]=1 False / True / Auto http://www.tyan.com...
  • Page 115 Program Rate value for DRAM Corrected Error Counter function. Only meaningful when PcdAmdDdrEccErrorCounterEnable is set to LeakMode(Value:0x00-0x1F). DRAM Corrected Error Counter Start Program starting count value for DRAM Corrected Error Counter function. Only meaningful when PcdAmdDdrEccErrorCounterEnable is not Disable(0x00 – 0xFFFF). FFFF5 http://www.tyan.com...
  • Page 116 Disabled / 1 hour / 4 hours / 6 hours / 8 hours / 12 hours / 16 hours / 24 hours / 48 hours DRAM Error Threshold Count List of Values: 0=ETC_4, 1=ETC_16, 2=ETC_64, 3=ETC_256(default – Auto), 4 = ETC_1024, 5 = ETC_4096, Auto http://www.tyan.com...
  • Page 117 DRAM x4 WriteBack Suppression To enable/Disable X4 device Error Correction Writeback suppression 0: ECS Writeback Suppression Disabled 1: ECS Writeback Suppression Enabled 0xFF: Auto – ABL chooses Writeback Suppression to be Enabled by default Disabled / Enabled / Auto http://www.tyan.com...
  • Page 118 DRAM ECC Enable Use this option to enable / disable DRAM ECC. Auto will set ECC to enable. Disabled / Enabled / Auto DRAM UECC Retry DRAM UECC Retry. Program to UMC:: RecCtrl.RecEn [2] Auto / Disabled / Enabled http://www.tyan.com...
  • Page 119 3.5.3.4 DDR Security Submenu TSME Transparent Secure Memory Encryption Auto / Disabled / Enabled Data Scramble Data Scrambling Enabled / Disabled http://www.tyan.com...
  • Page 120 PCIe ARI Support Enables Alternative Routing-ID Interpretation Disabled / Enabled / Auto PCIe Ten Bit Tag Support Enables PCIe ten bit tags for supported devices. Auto = Disable Disabled / Enabled / Auto SMU Common Options NBIO RAS Common Options http://www.tyan.com...
  • Page 121 SMU Common Options Submenu TDP Control Auto = Use the fused TDP Manual = User can set customized TDP Manual / Auto PPT Control Auto = Use the fused PPT Manual = User can set customized PPT Manual / Auto http://www.tyan.com...
  • Page 122 Enable or Disable Data Fabric to go to a low-power state when the processor has entered Cx states Disabled / Enabled / Auto CPPC Enable = Enable the feature : Disable = Disable the feature Disabled / Enabled / Auto HSMP Support Select HSMP support enable or disable Disabled / Enabled / Auto http://www.tyan.com...
  • Page 123 NBIO SyncFlood Generation This value may be used to mask SyncFlood caused by NBIO RAS options. When set to TRUE syncFlood from NBIO is masked. When set to FALSE NBIO is capable of generating SyncFlood. Disabled / Enabled / Auto http://www.tyan.com...
  • Page 124 Firmware First / Firmware First but allow OS First / OS First / Auto Edpc Control (0) Disabled; (1) Enabled; (3) Auto Enabled / Disabled / Auto ACS RAS Request Value No help string Direct Request Access Enabled / Request Blocking Enabled / Request Redirect Enabled / Auto http://www.tyan.com...
  • Page 125 True. When ‘Sync Flood on PCIe Fatal Error’ is False, PcdAmdPcieSyncFloodOnFatal should be set to False. When ‘Sync Flood on PCIe Fatal Error’ is Auto. PcdAmdPcieSyncFloodOnFatal Auto / True / False 3.5.5 FCH Common Options Submenu Ac Power Loss Options FCH RAS Options http://www.tyan.com...
  • Page 126 3.5.5.1 AC Power LOSS Options Submenu Restore Ac Power Loss Select Restore AC Power Loss Method Power Off / Power On / Last State http://www.tyan.com...
  • Page 127 3.5.5.2 FCH RAS Options Submenu Reset After Sync flood Enable AB to forward downstream sync-flood message to system controller. Disabled / Enabled / Auto http://www.tyan.com...
  • Page 128 Soc Miscellaneous Control Submenu ABL Console Out Control Enable: Enable ConsoleOut Function for ABL Disable: Disable ConsoleOut Function for ABL Auto: Keep default behavior Disabled / Enabled / Auto PSP error injection support Enable EINJ support False / True http://www.tyan.com...
  • Page 129 3.5.7 AMD PBS Submenu AMD CPM RAS related settings http://www.tyan.com...
  • Page 130 Pcie Device Uncorrected Error Sev Reg Initialize the PCIe AER Uncorrected Error Severity registers of PCIe Device DDR4 DRAM Hard Post Package Repair This feature allows spare DRAM rows to replace malfunctioning rows via an in-field repair mechanism. Disabled / Enabled http://www.tyan.com...

  • Page 131: Server Management

    OS Watchdog Timer If enabled, starts a BIOS timer which can only be shut off by management Software after the OS loads. Helps determine that the OS successfully loaded or follows the OS Boot Watchdog Timer policy. Disabled / Enabled http://www.tyan.com...
  • Page 132 Enable or Disable BMC logo Disabled / Enabled System Event Log Press<Enter> to change the SEL event log configuration. BMC network configuration Configure BMC network parameters BMC User Settings Press<Enter> to Add. Delete and Set Privilege level for users. http://www.tyan.com...
  • Page 133 No / Yes, on next reset / Yes, on every reset Log EFI Status Codes Disable the logging of EFI Status Codes or log only error code or only progress code or both. Both / Disabled / Error Code / Progress Code http://www.tyan.com...
  • Page 134 3.6.2 BMC Network Configuration Submenu http://www.tyan.com...
  • Page 135 Configuration Address Source Select the configure LAN channel parameters statically or dynamically (by BIOS or BMC). Unspecified option will not modify any BMC network parameters during BIOS phase. Unspecified / Static / DynamicBmcDhcp / DynamicBmcNonDhcp http://www.tyan.com...
  • Page 136 3.6.3 BMC User Configuration Submenu Add User Press <Enter> to Add a User. Delete User Press<Enter> to Delete a User. Change User Settings Press<Enter> to Change User Settings. http://www.tyan.com...
  • Page 137 3.6.3.1 BMC User Configuration Submenu http://www.tyan.com...
  • Page 138 3.6.3.2 Delete User Configuration Submenu http://www.tyan.com...
  • Page 139 3.6.3.3 Change User Configuration Submenu http://www.tyan.com...

  • Page 140: Security

    3.7 Security Administrator Password Set Administrator Password. User Password Set User Password. Security Frozen Mode Enable or disable HDD security freeze lock. Disable to support secure erase function. Disabled / Enabled Secure Boot Customizable Secure Boot settings http://www.tyan.com...
  • Page 141 When Secure Boot Mode was set to [Custom], the following items will be available to set up. Restore Factory Keys Force System to User Mode. Install factory default Secure Boot key databases Reset To Setup Mode Delete all Secure Boot Key databases from NVRAM http://www.tyan.com...
  • Page 142 Force System to User Mode. Install Factory Default Secure Boot key databases. Reset To Setup Mode Delete all Secure Boot Key database from NVRAM Enroll Efi Image Allow the image to run in Secure Boot mode. Enroll SHA256 hash certificate of a PE image into Authorized Signature Database (db) http://www.tyan.com...
  • Page 143 EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image(SHA256) Key Source: Default, External, Mixed Forbidden Signatures Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate in: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER) c) EFI_CERT_RSA2048 (bin) http://www.tyan.com...
  • Page 144 OsRecovery Signatures Enroll Factory Defaults or load certificates from a file: 1. Public Key Certificate in: a) EFI_SIGNATURE_LIST b) EFI_CERT_X509 (DER encoded) c) EFI_CERT_RSA2048 (bin) d) EFI_CERT_SHAXXX 2. Authenticated UEFI Variable 3. EFI PE/COFF Image(SHA256) Key Source: Default, External, Mixed http://www.tyan.com...

  • Page 145: Boot

    Enable or disable Quiet Boot option. Disabled / Enabled Endless Boot Enabled or Disabled Endless boot Disabled / Enabled Wait for “ESC” if Error Enabled or Disabled Wait ESC key Function. When chassis intrusion, CMOS Clear or BMC not Response. Disabled / Enabled http://www.tyan.com...
  • Page 146 USB Device BBS Priorities Set the order of the legacy devices in this group Add New Boot Option Add a new EFI boot option to the boot order Delete Boot Option Remove an EFI boot option from the boot order http://www.tyan.com...
  • Page 147 3.8.1 Add Boot Option Configuration Add boot option Create new boot option Path for boot option Enter the path to the boot option in the format Fs0:\path\ filename.efi Create Creates the newly formed boot option http://www.tyan.com...
  • Page 148 3.8.1 Delete Boot Option Configuration Delete Boot Option Remove an EFI boot option from the boot order. Device Name / Select one to Delete http://www.tyan.com...

  • Page 149: Save & Exit

    Reset system setup without saving any changes. Save Changes Save changes done so far to any of the setup options. Discard Changes Discard changes done so far to any of the setup options. Restore Defaults Restore/Load Default values for all the setup options. http://www.tyan.com...
  • Page 150 Save as User Defaults Save the changes done so far as User Defaults. Restore User Defaults Restore the User Defaults to all the setup options. Boot Override Device Name http://www.tyan.com...

  • Page 151: Chapter 4: Diagnostics

    BIOS flash failure, you must contact your dealer for a replacement BIOS. There are no exceptions. TYAN does not have a policy for replacing BIOS chips directly with end users. In no event will TYAN be held responsible for damages done by the end user.

  • Page 152: Amibios Post Code (Aptio)

    South Bridge initialization before microcode loading 0x05 OEM initialization before microcode loading 0x06 Microcode loading 0x07 AP initialization after microcode loading 0x08 North Bridge initialization after microcode loading 0x09 South Bridge initialization after microcode loading 0x0A OEM initialization after microcode loading 0x0B Cache initialization http://www.tyan.com...
  • Page 153 Memory initialization. Configuring memory 0x2F Memory initialization (other) 0x30 Reserved for ASL (see ASL Status Codes section below) 0x31 Memory Installed 0x32 CPU post-memory initialization is started. 0x33 CPU post-memory initialization. Cache initialization CPU post-memory initialization. Application Processor(s) (AP) 0x34 initialization http://www.tyan.com...
  • Page 154 S3 Resume Progress Codes 0xE0 S3 Resume is started (S3 Resume PPI is called by the DXE IPL). 0xE1 S3 Boot Script execution 0xE2 Video repost 0xE3 OS S3 wake vector call 0xE4 – 0xE7 Reserved for future AMI progress codes http://www.tyan.com...
  • Page 155 DXEIPL was not found. DXE Core Firmware Volume was not found. Recovery failed S3 Resume failed Reset PPI is not available. DXE Phase Status Code Description 0x60 DXE Core is started. 0x61 NVRAM initialization 0x62 Installation of the South Bridge Runtime Services http://www.tyan.com...
  • Page 156 PCI Bus Hot Plug Controller initialization 0x94 PCI Bus Enumeration 0x95 PCI BUS Request Resources 0x96 PCI Bus Assign Resources 0x97 Console output devices connect 0x98 Console Input devices connect 0x99 Super IO initialization 0x9A USB initialization is started. http://www.tyan.com...
  • Page 157 0xC0 – 0xCF OEM BDS initialization codes DXE Error Codes 0xD0 CPU initialization error 0xD1 North Bridge initialization error 0xD2 South Bridge initialization error 0xD3 Some of the Architectural Protocols are not available 0xD4 PCI resource allocation error. Out of Resources http://www.tyan.com...
  • Page 158 System is waking up from the S3 sleep state. 0x40 System is waking up from the S4 sleep state. System has transitioned into ACPI mode. Interrupt controller is in 0xAC APIC mode. System has transitioned into ACPI mode. Interrupt controller is in 0xAA APIC mode. http://www.tyan.com...

  • Page 159: Appendix I: Fan And Temp Sensors

    (rpm) Temp Sensor: SYS_Air_Outlet(RT3) ,and MB_Air_Inlet(RT2) etc. They detect the system temperature around. NOTE: The system temperature is measured in a scale defined by AMD, not in Fahrenheit or Celsius. http://www.tyan.com...
  • Page 160 BIOS Temp Sensor Name Explanation: http://www.tyan.com...
  • Page 161 P0_DIM_H0 Temperature of CPU0 DIMM Channel H0 P0_DIM_I0 Temperature of CPU0 DIMM Channel I0 SYS_FAN_1 Fan Speed of SYS_FAN_1 SYS_FAN_2 Fan Speed of SYS_FAN_2 SYS_FAN_3 Fan Speed of SYS_FAN_3 SYS_FAN_4 Fan Speed of SYS_FAN_4 SYS_FAN_5 Fan Speed of SYS_FAN_5 http://www.tyan.com...
  • Page 162 NOTE http://www.tyan.com...

  • Page 163: Appendix Ii: How To Recover Uefi Bios

    UEFI recovery bootloader that would prevent the recovery process itself from working. In no event shall Tyan be liable for direct, indirect, incidental, special or consequential damages arising from the BIOS update or recovery.
  • Page 164 “Flash update completed. Press any key to reset the system” displayed on screen. 8.Remove the USB disk and reboot. If your system does not have video output or the POST code halts at “FF” on the right-lower portion of the screen, please contact Tyan representatives for RMA service. http://www.tyan.com...

  • Page 165: Glossary

    (reading to or writing from a disk drive a single time is much faster than doing so repeatedly) there is the possibility of losing your data should the system crash. Information in a buffer is temporarily stored, not permanently saved. http://www.tyan.com...
  • Page 166 (like soundcards or keyboards) to access the main memory without involving the CPU. This frees up CPU resources for other tasks. As with IRQs, it is vital that you do not double up devices on a single line. Plug-n-Play devices will take care of this for you. http://www.tyan.com...
  • Page 167 EEPROM (Electrically Erasable Programmable ROM): also called Flash BIOS, it is a ROM chip which can, unlike normal ROM, be updated. This allows you to keep ® up with changes in the BIOS programs without having to buy a new chip. TYAN ’s BIOS updates can be found at http://www.tyan.com...
  • Page 168 PXE (Preboot Execution Environment): one of four components that together make up the Wired for Management 2.0 baseline specification. PXE was designed to define a standard set of preboot protocol services within a client with the goal of allowing networked-based booting to boot using industry standard protocols. http://www.tyan.com...
  • Page 169 NVIDIA s (graphics communications processing units) and NVIDIA MCPs (media and processors). application Depending on the , NVIDIA SLI can deliver as much as two times the performance of a single GPU configuration. http://www.tyan.com...
  • Page 170 CPUs without damaging the sensitive CPU pins. The CPU is lightly placed in an open ZIF socket, and a lever is pulled down. This shifts the processor over and down, guiding it into the board and locking it into place. http://www.tyan.com...

  • Page 171: Technical Support

    ® If these options are not available for you then TYAN Computer Corporation can help. Besides designing innovative and quality products for over a decade, TYAN ® has continuously offered customers service beyond their expectations. TYAN website (www.tyan.com) provides easy-to-access FAQ searches and online Trouble Ticket creation as well as Instant Chat capabilities with our Support Agents.
  • Page 172 (RMA) number. The RMA number Should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. ® TYAN will pay to have the board shipped back to you. Notice for the USA Compliance Information Statement (Declaration of...

Table of Contents