VEVOR TS181A Manual
  1. Manuals
  2. Brands
  3. VEVOR Manuals
  4. Metal Detector
  5. TS181A
  6. Manual
VEVOR TS181A Manual

VEVOR TS181A Manual

Hide thumbs Also See for TS181A:

Advertisement

Table of Contents

Technical Support and E-Warranty Certificate www.vevor.com/support
METAL DETECTOR
MODEL:TS181A
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and doses not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

Advertisement

Table of Contents
loading

Related Manuals for VEVOR TS181A

Summary of Contents for VEVOR TS181A

  • Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support METAL DETECTOR MODEL:TS181A We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us.

  • Page 2: Metal Detector

    CustomerService@vevor.com This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
  • Page 3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. This product is subject to the provision of European Directive 2012/19/EC.

  • Page 4: Technical Specification

    •Waterproof search coil •3.5mm earphone jack TECHNICAL SPECIFICATION Maximum Detection Distance: About 10 inches for a US 25-cent coin Operating Environment: Temperature: 0°C ~ 50°C Relative Humidity: 85% Storage Environment: Temperature: -20°C ~ 50°C Relative Humidity: 85% Battery: 1.5V alkaline battery, AA or equivalent, 6 pieces Weight: About 1.4kg ( including battery ) FRONT PANEL - 3 -...
  • Page 5 1. Depth Scale This depth scale is to be used in conjunction with the displayed target depth indicator bar for target depth prediction. 2. Target ID Legend Works with the Target ID Cursor to indicate the probable metal type of the detected metallic object.

  • Page 6: Understanding The Display

    In CUSTOM mode, this button is used to eliminate or activate the pixel located on the horizontal scale, directly below the Target ID Cursor. 8. "SENSITIVITY/MODE SELECTION" Button In All Metals Mode, this "SENSITIVITY/MODE SELECTION" button is used to adjust the detector's sensitivity. In any Discrimination Mode, you can press the "...
  • Page 7 ..The metal detector is in COINS mode..The metal detector is in DEBRIS mode..The metal detector is in ORNAMENTS mode..The metal detector is in CUSTOM mode..The metal detector is in All Metals Mode..The metal detector is in sensitivity adjustment mode..The metal detector is in PINPOINT mode.
  • Page 8 STRUCTURE / ASSEMBLY INSTRUCTION Overall Structure - 7 -...
  • Page 9 Upper Part Structure - 8 -...
  • Page 10 Assembly Drawing - 9 -...
  • Page 11 Note: 1. The two rubber washers are to be placed in the two circular slots at the two sides of the end of the lower stem before slipping the search coil onto the end of the lower stem. 2. Gently turn the relevant stem lock nut on the middle stem in proper direction to fasten the lower stem only after the lower stem is inserted into the middle stem and the two buttons on the lower stem pop into desired holes on the middle stem.

  • Page 12: Target Information

    TARGET INFORMATION Target ID Legend The Target ID Legend functions with the Target ID Cursor to indicate the probable metal type of the target, with ferrous ( iron ) targets at the left, non-ferrous targets which are thin or have low conductivity in the middle, and thick or high conductivity targets at the right.
  • Page 13 Digital Target ID Provides a two-digits number to identify target more precisely than the Target ID Cursor. Target ID can vary widely based on the target's size and thickness because small, thin pieces of metal can not conduct electric current as well as thicker pieces of metal. Moreover, mineralized soils can cause Target ID errors, especially for small targets.
  • Page 14 8 is expressed using words and is far more detailed than the information contained on the Target ID Legend. You can use Figure 8 in conjunction with the target ID cursor like you use the Target ID Legend. Coins will most likely have a similar value with each pass with the search coil due to their round shape.
  • Page 15 DETECTING METALLIC OBJECTS DETECTING METALLIC OBJECTS IN THE ALL METALS MODE The All Metals Mode allows the detector to achieve the maximum detection depth possible. Press the ON/OFF button to turn on the metal detector. To select the All Metals Mode, press the "ALL-METAL/DISC" button until the symbol "ALL METALS"...
  • Page 16 4. Lower the search coil to approximately 5cm to 8cm above ground. If the sound from the detector increases when the search coil is lowered to ground, raise the search coil to about 50cm above ground, and then press the " - " side of the "GROUND BALANCE/CUSTOM SELECTION" button to decrease the ground balance setting.
  • Page 17 When the detector detects a metallic object, a target ID cursor will appear in a certain position to indicate the probable metal type of the object being detected and a digital target ID, which is a two-digits number, will be shown on the display if the strength of the detected metal signal exceeds the detector's identification threshold, and at the same time, and if the target is accepted by a lighted pixel on the horizontal scale, the sound from the...
  • Page 18 Use the following procedure to pinpoint a target: 1. Move the search coil around the detected metallic object to determine approximate location of this object. Then move the search coil to this location, and then hold the search coil in this location and above the detected object.
  • Page 19 The detector has 12 pixels or "notches" of discrimination, shown on the horizontal scale ( see Figures 2 and 7 ). In any Discrimination Mode, the detected target which is accepted by a lighted pixel on the horizontal scale will cause an increase in sound, and the targets which are rejected by a blank pixel on the horizontal scale will probably not cause an increase in sound.
  • Page 20 The DEBRIS mode is designed to detect debris while eliminating ( ignoring ) small iron pieces. •ORNAMENTS Mode The ORNAMENTS mode is designed to detect most kinds of metallic ornaments. •CUSTOM Mode The detector has 12 pixels or " notches " of discrimination, shown on the horizontal scale.
  • Page 21 After you have selected a desired Discrimination Mode or created a desired discrimination pattern in the CUSTOM mode, you can start to scan for metallic object or target. The scanning method is the same as that in the All Metals Mode.

  • Page 22: Using The Backlight

    only for non-critical reference. The target ID cursor indication and digital target ID are not guaranteed to be correct. When the detected metal signal is strong enough, the display will show a target depth indicator bar, which is to be used in conjunction with the depth scale for you to predict the distance between the detected object and the search coil.

  • Page 23: Using The Earphone

    CHANGING THE OPERATING CHANNEL OF THE DETECTOR When there are two same metal detectors operating in the same site, you can set them to two different operating channels to avoid crosstalk ( interference ) between them. When the detector is turned on, it defaults to channel 0. You can press and hold down the "...

  • Page 24: Troubleshooting

    TROUBLESHOOTING SYMPTOM SOLUTION The detector can 1. Make sure that the batteries are installed in correct not be turned on. orientation. 2. Replace the old batteries with new ones of the same type. Erratic sounds or 1. Ensure that the search coil is securely connected and that target ID cursor the search coil cable is snugly wound around the stem.

  • Page 25: Battery Replacement

    Target ID Cursor If Target ID Cursor bounces erratically, the detector may bounces have detected a junk object or the metal signal is too weak. However, Target ID Cursor may bounce if a good target ( such as a coin ) is not parallel to the search coil or the target is below the edge of the search coil.
  • Page 26 NOTE •Turn off the detector when not in use. •If the detector operates abnormally, a possible cause is that the batteries are exhausted. Replace the batteries if necessary. •Protect the plug of the search coil cable from damp; otherwise the detector may lose its detecting ability.
  • Page 27 3. The contents of this manual can not be used as the reason to use the detector for any special application. Address：Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai Imported to USA: VEVOR STORE INC, 9448 RINCHMOND PL #E RANCHO CUCAMONGA, California, 91730 United States of America SHUNSHUN GmbH Römeräcker 9 Z2021, 76351...
  • Page 28 Technical Support and E-Warranty Certificate www.vevor.com/support...

Table of Contents