Surfaces In The Cooking Compartment - Siemens NB535AB 0B Series Instruction Manual

Door panels Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
Do not use a glass scraper or a stainless steel
scouring pad.
Door handle Hot soapy water:
Clean with a dish cloth and then dry with a soft
cloth.
If descaler comes into contact with the door han-
dle, wipe it off immediately. Otherwise, any stains
will not be able to be removed.
Appliance interior
Enamel surfaces Observe the instructions for the surfaces of the
and self-cleaning cooking compartment that follow the table.
surfaces
Glass cover for Hot soapy water:
the interior light- Clean with a dish cloth and then dry with a soft
ing cloth.
If the cooking compartment is heavily soiled, use
oven cleaner.
Door seal Hot soapy water:
Clean with a dish cloth.
Do not remove.
Do not scour.
Door cover made from stainless steel:
Use stainless steel cleaner. Follow the manufac-
turers' instructions. Do not use stainless steel
care products.
made from plastic:
Clean using hot soapy water and a dish cloth. Dry
with a soft cloth. Do not use glass cleaner or a
glass scraper.
Remove the door cover for cleaning.
Rails Hot soapy water:
Soak and clean with a dish cloth or brush.
Pull-out system Hot soapy water:
Clean with a dish cloth or a brush.
Do not remove the lubricant while the pull-out rails
are pulled out – it is best to clean them when they
are pushed in. Do not clean in the dishwasher.
Accessories Hot soapy water:
Soak and clean with a dish cloth or brush.
If there are heavy deposits of dirt, use a stainless
steel scouring pad.
--------
Notes
Slight differences in colour on the front of the
■
appliance are caused by the use of different
materials, such as glass, plastic and metal.
Shadows on the door panels, which look like
■
streaks, are caused by reflections made by the
interior lighting.
Enamel is baked on at very high temperatures.This
■
can cause some slight colour variation. This is
normal and does not affect operation.
The edges of thin trays cannot be completely
enamelled. As a result, these edges can be rough.
This does not impair the anti-corrosion protection.

Surfaces in the cooking compartment

Enamel surfaces are smooth. Self-cleaning surfaces are
rough.
Cooking compart- Main oven
ment surface
Enamel surfaces Cooking compart-
ment floor, ceiling
and side sections
Self-cleaning surfaces Back wall
Cleaning enamel surfaces
Clean the smooth enamel surfaces with a dish cloth
and hot soapy water or a vinegar solution. Then dry
them with a soft cloth.
Soften baked-on food remnants with a damp cloth and
soapy water. Use stainless steel wire wool or oven
cleaner to remove stubborn dirt.
Caution!
Never use oven cleaner in the cooking compartment
when it is still warm. This may damage the enamel.
Remove all food remnants from the cooking
compartment and the appliance door before you next
heat up the appliance.
Leave the cooking compartment open to dry after
cleaning it.
Food residues can cause white deposits to form.
Note:
These are harmless and do not affect how the
appliance works. You can remove these residues using
lemon juice if required.
Cleaning self-cleaning surfaces
The self-cleaning surfaces are coated with a porous,
matt ceramic layer. This coating absorbs and dispels
splashes from baking and roasting while the appliance
is in operation.
If the self-cleaning surfaces no longer clean themselves
sufficiently and dark patches appear, they can be
cleaned by running a program specifically to heat them
up.
Caution!
Do not use oven cleaner on the self-cleaning surfaces.
This will damage the surfaces. If oven cleaner does get
onto these surfaces, dab it off immediately using water
and a sponge cloth. Do not rub the surface and do not
use abrasive cleaning aids.
Main oven
Remove shelf supports, rails, accessories and
ovenware from the cooking compartment. Thoroughly
clean the smooth enamel surfaces in the cooking
compartment, the inside of the appliance door and the
glass cover on the interior lighting.
Set the hot air type of heating for the main oven.
1.
Set the maximum temperature.
2.
Start the mode and leave it to run for at least one
3.
hour.
This will regenerate the ceramic coating.
Cleaning agent
en
Top oven
Cooking compart-
ment floor
Back wall, ceiling and
side sections
19