Page 1
INSTALLATION OPERATING INSTRUCTIONS Models: Start with the prefix QST or ECO 4000: 350E, 350L, 500E, 500L ECO-4000 INTENDED FOR OTHER THAN HOUSEHOLD USE RETAIN THIS MANUAL FOR FUTURE REFERENCE UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
3. Never touch quartz or steel heaters. Warranty Information: Reliability Backed By APW Wyott’s Warranty: All APW Wyott Toaster Ovens are backed by a one year parts and labor warranty, including On-Site Service calls within 50 miles of authorized service technicians. Service Information:...
Safety Signs and Messages The following Safety signs and messages are placed in this manual to provide instructions and identify specific areas where potential hazards exist and special precautions should be taken. Know and understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or serious injury to you or other persons may result if these messages are not followed.
INSTALLATION INSTRUCTIONS If the carton appears damaged, or damage is discovered once the carton is opened, stop immediately and contact the freight company to file a damage claim. CAUTION: The ECO TOASTER Oven is shipped assembled except for installation of the crumb tray assembly.
OPERATION 1. The controls that operate the belt conveyor speed and the heaters are located on the front of the unit. 2. The On/Off switch is used to turn the unit on or off. Once the unit is turned on the conveyor will automatically run.
Page 6
3. The display will display a “-“then the word “HEAT” when the unit has completed its heat up cycle it will display “IdLE.” 4. After the display shows “IdLE” the unit is ready to use. 5. Press the “OTHER” Button located at the right side of the control panel. 6.
PROGRAMMING INSTRUCTIONS (ELECTRONIC – “E” MODELS) Product Key Programming Toast Button 1. Press and hold the “LIGHTER” and “DARKER” buttons simultaneously for 20 seconds. 2. The display will display “PROG”. 3. Press the “TOAST” Button. 4. The Display will display “sped” then the current speed setting numeric value. 5.
4. The display will display “sped” then the current speed setting numeric value. 5. Pressing the “DARKER” button will increase the numeric value, increasing the conveyor speed. Pressing the “LIGHTER” button will decrease the numeric value, which will decrease the conveyor speed.
Using a damp rag with mild soap solution, wipe down all areas of the conveyor. DO NOT ATTEMPT TO • CLEAN THE QUARTZ OR METAL HEATERS. When units are in the stacked configuration, it is still necessary to clean between the units. Using a damp •...
Page 12
PARTS LISTS & EXPLODED VIEWS EXPLODED VIEW 500E...
PARTS LISTS & EXPLODED VIEWS ECO 4000 500E Parts Lists Item Part # Title Item Part # Title Item Part # Title 86621-00 LEG 1" CHROME 15346-00 CORD, 14/3 HSJO NEMA 6-20P 72" 48395600 DRIVE SHAFT ASSY SEGMENTED BELT 21851450 COVER, ELEMENT CART.
Page 14
PARTS LISTS & EXPLODED VIEWS ECO 4000 500L...
Page 15
PARTS LISTS & EXPLODED VIEWS ECO 4000 500L Parts List Item Part Number Title Item Part Number Title 86621-00 LEG 1" CHROME 44 21851439 TRAY CRUMB 21851482 ELEMENT, 208V 1400W 46 21851464 PANEL, CONTROL QST VL 21851453 BRACKET, ELEMENT CART. 47 21851458 SIDE, CONVEYOR LS QST MOUNTING (L) QST...
Page 17
Authorized Service Agencies. The use of other than APW Wyott Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated with same. The closest APW Wyott Authorized Service Agent must be used.
Need help?
Do you have a question about the ECO 4000-350E and is the answer not in the manual?
Questions and answers