Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PERCo IR-04.1
Summary of Contents for PERCo IR-04.1
- Page 1 Proximity Reader IR-04.1 CERTIFICATE ASSEMBLY AND OPERATION MANUAL...
- Page 2 Proximity Reader IR-04.1 Certificate, Assembly and Operation Manual TC RU C-RU.МЛ02.В.00368 ТУ 4372-034-88226999-2012...
-
Page 3: Table Of Contents
INSTALLATION INSTRUCTIONS ................6 Installation details ....................6 Cables parameters....................6 Installation tools ....................7 Installation procedure..................7 POSSIBLE FAULTS AND REMEDY ................9 PERCo WARRANTY....................9 WARRANTY CARD ......................11 ... -
Page 4: General Information
1 GENERAL INFORMATION Proximity reader IR-04.1 (hereinafter – the reader) is designed for reading and decoding the code logged into the proximity identifier and its transfer to the controller of PERCo system operating device. The reader with regard to resistance to environmental exposure complies with GOST 15150-69, category NF1 (operation in premises with climate control). -
Page 5: Delivery Set
(central) light indicator’s state (switches off if the light was on and switches on if the light was off). Maximum distance between the reader and external controller depends on the cable cross-section. For selecting the cable type please contact PERCo specialists. -
Page 6: Operation Principle
IR-04.1 Proximity Reader 4.2 Operation principle Readers provide code reading from Proximity identifiers with operation frequency 125 kHz (hereinafter – the identifier) produced by HID Corporation type ProxCard II, ISOProx II, trinkets ProxKey II (standard formats HID: 26 bit (H10301), 37 bit (H10302, H10304)), and the production of EM-Microelectronic-Marin SA. -
Page 7: Installation Instructions
2×2×0.52 (max. distance – 50 m). At a greater distance, a cable with a large cross-section of cores should be used. Note: Maximum distance between the reader and external controller is 200 m and depends on the cable cross-section. For selecting the cable type please contact PERCo specialists. -
Page 8: Installation Tools
Ø5 mm hard-alloyed drill bits; Flat slot screwdriver No2; Mounting knife; Level; Measuring tape (2 m). Figure 3 – IR-04.1 reader installation Figure 4 – Jumpers «reader number» layout (reader housing is dotted) (XP2), jumper «switch off end-of-line resistor» (XP1) 6.4 Installation procedure... - Page 9 7. Lay the cable, fix it and connect to PERCo system controller (connection layout is shown in Fig. 5 and in controller manual). For extension of a reader cable the twisted pair cable must be used provided that A and B signal lines are in one pair.
-
Page 10: Possible Faults And Remedy
If the fault is not cleared please contact the Manufacturer. 8 PERCO WARRANTY PERCo (the Manufacturer) warrants that the IR-04.1 proximity reader complies with applicable statutory safety requirements, electromagnetic compatibility provided that the instructions on storage, installation and operation, given in the Assembly & Operation Manual are observed. - Page 11 SOPHISTICATED PRODUCTS THAT, IF NOT FAULTY, CANNOT BE RETURNED BACK IF BY SOME REASON THE CUSTOMER DEEMS THEM UNSATISFACTORY The PERCo IR-04.1 proximity reader is in conformity with the essential requirements of the EU’s Machinery, Low-Voltage and EMC Directives and carries the CE marking accordingly.
-
Page 12: Warranty Card
WARRANTY CARD IR-04.1 Proximity reader Serial number Date of manufacture ____________________ 20___ Quality Control Seal _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Date of sale «... - Page 13 PERCo Polytechnicheskaya str., 4, block 2 194021, Saint Petersburg Russia Tel: +7 812 247 04 64 E-mail: export@perco.com support@perco.com www.perco.com...
- Page 14 www.perco.com...
Need help?
Do you have a question about the IR-04.1 and is the answer not in the manual?
Questions and answers