Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PERCo IR-03.1
Summary of Contents for PERCo IR-03.1
- Page 1 Proximity Reader IR-03.1 CERTIFICATE ASSEMBLY AND OPERATION MANUAL...
- Page 2 Proximity Reader IR-03.1 Certificate, Assembly and Operation Manual TC RU C-RU.МЛ02.B.00368 ТУ 4372-034-88226999-2012...
-
Page 3: Table Of Contents
INSTALLATION INSTRUCTIONS ................6 Installation details ....................6 Cables parameters....................6 Installation tools ....................7 Installation procedure..................7 POSSIBLE FAULTS AND REMEDY ................9 PERCo WARRANTY....................9 WARRANTY CARD ......................11 ... -
Page 4: General Information
1 GENERAL INFORMATION Proximity reader IR-03.1 (hereinafter – the reader) is designed for reading and decoding the code logged into the proximity identifier and its transfer to the controller of PERCo system operating device. Colour of the reader housing is marked by the end letter: IR-03.1B –... -
Page 5: Delivery Set
Reference of the reader number to a passage direction is programmed by the software. Maximum distance between the reader and external controller depends on the cable cross-section. For selecting the cable type please contact PERCo specialists. -
Page 6: Operation Principle
IR-03.1 Proximity Reader For reader mounting a metal base-plate is included in delivery set. The metal base-plate has 4 holes to fix it with screws to mounting surface. Reader is fixed to metal base-plate with a screw in lower part of reader housing. -
Page 7: Installation Instructions
2×2×0.52 (max. distance – 50 m). At a greater distance, a cable with a large cross-section of cores should be used. Note: Maximum distance between the reader and external controller is 200 m and depends on the cable cross-section. For selecting the cable type please contact PERCo specialists. -
Page 8: Installation Tools
Flat slot screwdriver No2; Mounting knife; Level; Measuring tape (2 m). Figure 3. IR-03.1 reader installation layout Figure 4. Piezoelectric element (B1), (reader housing is dotted) jumpers «reader number» (XP2), jumper «switch off end-of-line resistor» (XP1) 6.4 Installation procedure... - Page 9 7. Lay the cable, fix it and connect to PERCo system controller (connection layout is shown in Fig. 5 and in controller manual). For extension of a reader cable the twisted pair cable must be used provided that A and B signal lines are in one pair.
-
Page 10: Possible Faults And Remedy
If the fault is not cleared please contact the Manufacturer. 8 PERCO WARRANTY PERCo (the Manufacturer) warrants that the IR-03.1 proximity reader complies with applicable statutory safety requirements, electromagnetic compatibility provided that the instructions on storage, installation and operation, given in the Assembly & Operation Manual are observed. - Page 11 SOPHISTICATED PRODUCTS THAT, IF NOT FAULTY, CANNOT BE RETURNED BACK IF BY SOME REASON THE CUSTOMER DEEMS THEM UNSATISFACTORY The PERCo IR-03.1 proximity reader is in conformity with the essential requirements of the EU’s Machinery, Low-Voltage and EMC Directives and carries the CE marking accordingly.
-
Page 12: Warranty Card
WARRANTY CARD IR-03.1 Proximity reader Serial number Date of manufacture ____________________ 20___ Quality Control Seal _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Date of sale «... - Page 13 PERCo Polytechnicheskaya str., 4, block 2 194021, Saint Petersburg Russia Tel: +7 812 247 04 64 E-mail: export@perco.com support@perco.com www.perco.com...
- Page 14 www.perco.com...
Need help?
Do you have a question about the IR-03.1 and is the answer not in the manual?
Questions and answers