Page 1
fixing devices from those supplied. Phillips & Flathead screwdrivers and hammer required. *We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Zara Six Drawer Panel layout Insert 6x bolts (C) into panel [1]. Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 3
(E). Tighten with a screwdriver. Insert 4x bolts (C) into panels [6]. 3x slide rails (T) to panel [4] and secure with 9x screws (E). Insert Tighten with a screwdriver. 4x bolts (C) into panel [4]. Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 4
Attach panels [7] to panel [6] with 2x long dowels (R) and secure with 4x Tighten with a screwdriver. Place 1x cover (N) over the bracket (M) locking nuts (D). Tighten with a screwdriver. as shown. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 5
4x locking nuts (D). Tighten with a screwdriver. with 4x locking nuts (D). Tighten with a screwdriver. Attach panel [8] to panel [6] secure with 2x long screws (B). Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 6
Slide panels [5] down along the grooves between the panels [3] and Attach panel [1] to panels [3], [4] and [6] with 6x dowels (A) and secure with [4] as shown. 6x locking nuts (D). Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 7
Attach 2x brackets (M) to panel [2] and secure with 4x screws (E). [4] as shown. Tighten with a screwdriver. Place 2x cover (N) over the bracket (M) as shown. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 8
Attach legs [40] and [41] to panel [2] using 20x bolts (G) as shown. Tighten with an Allen key (I). Insert the adjuster (P) into the middle support leg [41]. Attach 4x felt pads (L) to the ends of the legs [40]. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 9
Attach panels [30] and [31] to panel [32] secure with 24x screws (Q). Tighten a screwdriver. Attach 6x seal (O) to panel [35], [36] and [37] and with a screwdriver. secure with 6x screw (E). Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 10
Slide panel [33] down along the grooves between the panels [30] Attach panels [35], [36] and [37] to panels [30] and [31] secure with 24x and [31] as shown. locking nuts (D). Tighten with a screwdriver. mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 11
Ensure the drawers slide easily along the rails. If the door is not catching or sitting flush, twist the end of the cover (N) until it catches on the seal (O). mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...
Page 12
2x washers (Z), 2x wall anchors (X) and 2x wall screws (Y). Ensure using 2x washers (Z) and 2x screws (W). Tighten with a screwdriver. unit is balanced and steady before use. You’re done, enjoy! mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008...