Page 1
Phillips & Flathead screwdrivers For quicker assembly, we recommend the use of a power drill on a low-speed setting. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 2
Attach 2x bracket (M) to panel [1] and secure with 4x screws (E). Place 2x cover (N) over the bracket (M) as shown. Tighten with a 4x bolts (C) into panels [5] and [6]. Tighten with a screwdriver. screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 3
Attach panels [5] and [6] to panels [7] with 4x dowels (A) and secure with 4x Place 1x cover (N) over the bracket (M) as shown. Tighten with a locking nuts (D). Tighten with a screwdriver. screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 4
Slide panels [8] and [9] down along the grooves between panels with 8x locking nuts (D). Tighten with a screwdriver. [3], [4], [5] and [6] to form the back of the unit as shown. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 5
Attach panel [2] to panels [3] ,[4], [5] and [6] with 8x dowels (A) and secure with 8x screws (B). Tighten with a screwdriver. Place 1x cover (N) over the bracket (M) as shown. Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 6
24x bolts (L) Tighten with an Allen key (T). Screw the height adjuster (I) 2x screw (E). Tighten with a screwdriver. onto the legs [11]. Attach 4x felt pads (R) to the ends of the legs [10]. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 7
[14] onto them. Ensure the shelves are balanced If the cover (N) is not catching on the seal (O), adjust the magnetic end and stable. by twisting it outwards. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 8
Attach panel [16], [17] and [18] to panels [15] and secure with 5x and secure with 1x screw (E). Tighten with a screwdriver. locking nuts (D). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 9
Slide panel [19] along the grooves between the side panels [16] and [17]. Attach panels [16], [17], [18] and [20] as shown using 5x screws (S). Tighten with a screwdriver. mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 10
Ensure the drawers slide easily along the rails. If the drawer is not catching or sitting flush, twist the end of the cover (N) until it catches on the seal (O). mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...
Page 11
Fasten to the wall using 2x washers (Z), 2x wall anchors (X) 2x screws (W). Tighten with a screwdriver. and 2x screws (Y). Ensure unit is balanced and steady before use. You’re done, enjoy! mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore, QLD, 4558...