Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Midea P7 MAX
Summary of Contents for Midea P7 MAX
- Page 1 2 in 1 MIDEA Cordless Handstick 2 in 1 Cordless Handstick PLEASE READ THE MANUAL CAREFULLY BEFORE USING AND KEEP IT PROPERLY FOR FUTURE USE Importer: JH Electrical and Appliance Ltd P7 MAX 3C Short St, Newmarket, Auckland, MCS2129BG New Zealand...
-
Page 2: Safety Instructions
Safety Instructions - Do not place the vacuum cleaner close to heat sources, radiation sources or burning cigarette butts. Sucking in the following objects is strictly forbidden: 1. All liquids such as water and solvent; 2. Construction dust and trash such as lime and cement dust. 3. - Page 3 - Do not use the vacuum cleaner and send it to the maintenance department designated by Midea for maintenance in time under the following circumstances: 1. The vacuum cleaner has obvious damage or abnormal operation condition after falling to the floor 2.
-
Page 4: Introduction To The Product
Introduction to the Product Installation and Parts On/off button Mode button Dust bin release button Battery pack Dust empty button Tube release button Bend switch Electric brush release button List of accessories Motorized Upholstery Storage buckle Crevice Storage rack Adaptor Instructions bed brush brush... -
Page 5: Function Operation
Function Operation Use of bendable tube Pull upwards the upper sleeve of the bendable tube, and the bendable tube automatically rotates and bends. Battery charging Note 1. The battery is not charged when leaving the factory, so please fully charge the bat- 4. - Page 6 Function Operation Cleaning Note 1. To avoid blocking the air duct, please clean up large pieces of garbage (such as large piec- 4. It is strictly forbidden to remodel the complete machine, accessories and replace the power 5. Battery model: BP28825A Use of the machine Press the "On/Off button"...
-
Page 7: Cleaning And Maintenance
Cleaning and Maintenance Storage and use of the cleaner Note 1. When the cleaner is placed on the storage station or when the storage station is placed alone, it must be placed on a horizontal ground to avoid falling and damage to the cleaner. - Page 8 Cleaning and Maintenance Disassembling and cleaning of dust cup Note 1. To keep the suction of the vacuum cleaner, please clean the dust regularly, bottom cover of the dust cup to dump the dust. Dust full Press position with one hand and take out the dust cup assembly with the other hand. Push the button Note 1.
- Page 9 Cleaning and Maintenance Disassembling and cleaning of cyclone cone according to the disassembly procedure. Close Close Disassembl and cleaning of electric scrubbing brush Note 2. When disassembling and maintaining, be sure to stop the operation of the 3. It is not recommended to wash the scrubbing brush with water. The entan- gled hair can be cleaned with scissors or blades, and the dust stuck on the roller brush can be cleaned with a brush.
- Page 10 Cleaning and Maintenance Disassembl and cleaning of electric scrubbing brush Unscrew the gland of the roller brush according to the instructions, draw the roller brush assembly to one side and clean it. Mount it back according to the disassembly procedure after cleaning. Press Draw out the roller brush Release the gland of the...
- Page 11 Cleaning and Maintenance Disassembl and cleaning of electric scrubbing brush Note 1. When dust blocks the air duct of the bed brush, please use disposable chopsticks to remove the dust. 3. During operation, do not touch the roller brush that rolls at the bottom. and maintain the roller brush when it is entangled or dirty.
- Page 12 Cleaning and Maintenance one hand, rotate the air vent cover with the other hand counterclockwise, by brute force. After being fully dried, mount it back according to the above disassembly steps. Mounting and dismounting of battery pack Operation Instructions Press Press the battery pack release button Pull the battery pack backward Replace the battery pack...
-
Page 13: Troubleshooting
Troubleshooting Abnormality Possible Cause Treatment - Floor brush or mite removal brush entangled - Clean floor brush or mite removal 3 indicators during rolling brush flash - Too high or too low use - Please use in a proper environment ambient temperature - Large trash rolled in Electric floor...
Need help?
Do you have a question about the P7 MAX and is the answer not in the manual?
Questions and answers